- 您现在的位置：买卖IC网 > PDF目录1932 > LPC2103FBD48,151 (NXP Semiconductors)IC ARM7 MCU FLASH 32K 48-LQFP PDF资料下载
参数资料
| 型号： | LPC2103FBD48,151 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 9/37页 |
| 文件大小： | 0K |
| 描述： | IC ARM7 MCU FLASH 32K 48-LQFP |
| 产品培训模块： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs ARM7 Architecture ARM7 Memory |
| 标准包装： | 250 |
| 系列： | LPC2100 |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 70MHz |
| 连通性： | I²C，Microwire，SPI，SSI，SSP，UART/USART |
| 外围设备： | POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 32KB（32K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 8K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.65 V ~ 3.6 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-LQFP |
| 包装： | 托盘 |
| 产品目录页面： | 704 (CN2011-ZH PDF) |
| 配用： | 568-4310-ND - EVAL BOARD LPC2158 W/LCD 568-4302-ND - BOARD EVAL LPC210X KS2103 JLINK 568-4301-ND - BOARD EVAL LPC210X KS2103 568-4300-ND - BOARD EVAL LPC210X MCB2103 568-4297-ND - BOARD EVAL LPC21XX MCB2100 MCB2103UME-ND - BOARD EVAL MCB2103 + ULINK-ME MCB2103U-ND - BOARD EVAL MCB2103 + ULINK2 622-1013-ND - BOARD FOR LPC2103 48-LQFP 622-1008-ND - BOARD FOR LPC9103 10-HVSON 622-1005-ND - USB IN-CIRCUIT PROG ARM7 LPC2K |
| 其它名称： | 568-2094 935280966151 LPC2103FBD48-S |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
LPC2101_02_03_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 2 June 2009
17 of 37
NXP Semiconductors
LPC2101/02/03
Single-chip 16-bit/32-bit microcontrollers
Incorrect/Incomplete feed sequence causes reset/interrupt if enabled.
Flag to indicate watchdog reset.
Programmable 32-bit timer with internal pre-scaler.
Selectable time period from (TPCLK × 256 × 4) to (TPCLK × 232 × 4) in multiples of
TPCLK × 4.
6.16 Real-time clock
The Real-Time Clock (RTC) is designed to provide a set of counters to measure time
when normal or idle operating mode is selected. The RTC has been designed to use little
power, making it suitable for battery powered systems where the CPU is not running
continuously (Idle mode).
6.16.1 Features
Measures the passage of time to maintain a calendar and clock.
Ultra-low power design to support battery powered systems.
Provides Seconds, Minutes, Hours, Day of Month, Month, Year, Day of Week, and Day
of Year.
Can use either the RTC dedicated 32 kHz oscillator input or clock derived from the
external crystal/oscillator input at XTAL1. The programmable reference clock divider
allows ne adjustment of the RTC.
Dedicated power supply pin can be connected to a battery or the main 3.3 V.
6.17 System control
6.17.1 Crystal oscillator
The on-chip integrated oscillator operates with external crystal in range of 1 MHz to
25 MHz. The oscillator output frequency is called fosc and the ARM processor clock
frequency is referred to as CCLK for purposes of rate equations, etc. fosc and CCLK are
the same value unless the PLL is running and connected. Refer to Section 6.17.2 “PLL”
and Section 10.1 “XTAL1 input” for additional information.
6.17.2 PLL
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up into the range of 10 MHz to 70 MHz with a Current Controlled
Oscillator (CCO). The multiplier can be an integer value from 1 to 32 (in practice, the
multiplier value cannot be higher than 6 on this family of microcontrollers due to the upper
frequency limit of the CPU). The CCO operates in the range of 156 MHz to 320 MHz, so
there is an additional divider in the loop to keep the CCO within its frequency range while
the PLL is providing the desired output frequency. The output divider may be set to divide
by 2, 4, 8, or 16 to produce the output clock. Since the minimum output divider value is 2,
it is insured that the PLL output has a 50 % duty cycle. The PLL is turned off and
bypassed following a chip reset and may be enabled by software. The program must
congure and activate the PLL, wait for the PLL to lock, and then connect to the PLL as a
clock source. The PLL settling time is 100
s.
相关PDF资料 |
PDF描述 |
|---|---|
| LPC2106FBD48,151 | IC ARM7 MCU FLASH 128K 48-LQFP |
| LPC2292FBD144,551 | IC ARM7 MCU FLASH 256K 144-LQFP |
| LPC3240FET296,551 | IC ARM9 MCU 256K 296-TFBGA |
| LT1025ACN8 | IC THERMO COMPNSATR MICRPWR 8DIP |
| LT1030CS#PBF | IC LINE DRVR LOWPWR QUAD 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LPC2103FBD48CP3255 | 制造商:NXP Semiconductors 功能描述:- Tape and Reel |
| LPC2103FBD48-S | 制造商:NXP Semiconductors 功能描述:IC, 32BIT MCU, ARM7, 75MHZ, LQFP-48; Controller Family/Series:(ARM7); Core Size:32bit; No. of I/O's:32; Supply Voltage Min:1.65V; Supply Voltage Max:1.95V; Digital IC Case Style:LQFP; No. of Pins:48; Program Memory Size:32KB ;RoHS Compliant: Yes |
| LPC2103FBD48-T | 功能描述:ARM微控制器 - MCU 32K FL/8K RAM/8CH 10-B ADC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| LPC2103FHN48 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontrollers; 8 kB/16 kB/32 kB flash with ISP/IAP, fast ports and 10-bit ADC |
| LPC2103FHN48,551 | 功能描述:ARM微控制器 - MCU 32K FL/8K RAM 8CH 10-B ADC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。