- 您现在的位置：买卖IC网 > Datasheet目录988 > LPS1100H47R0JB (Vishay Sfernice)RESISTOR HEAT SINK 47 OHM 1100W Datasheet资料下载
参数资料
| 型号： | LPS1100H47R0JB |
| 厂商： | Vishay Sfernice |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | RESISTOR HEAT SINK 47 OHM 1100W |
| 标准包装： | 15 |
| 系列： | LPS1100 |
| 电阻（欧姆）： | 47 |
| 功率（瓦特）： | 1100W |
| 复合体： | 厚膜 |
| 特点： | 非电感 |
| 温度系数： | ±150ppm/°C |
| 容差： | ±5% |
| 安装特点： | 法兰 |
| 尺寸/尺寸： | 2.362" L x 2.244" W（60.00mm x 57.00mm） |
| 高度： | 1.000"（25.40mm） |
| 引线型： | M4 螺纹 |
| 包装： | 散装 |
| 封装/外壳： | 盒 |
| 其它名称： | LPS-47.0D |
LPS 1100
www.vishay.com
PERFORMANCE
Vishay Sfernice
TESTS
Momentary Overload
Rapid Temperature Change
Load Life
Humidity (Steady State)
Mechanical Shock
Vibration
Climatic Sequence
CONDITIONS
IEC 60115-1: 2 x P r /10 s for heatsink with
R th(h-a) ≥ 0.26 °C/W (maximum power: 700 W)
1.6 x P r /1 s for heatsink with 0.26 °C/W > R th(h-a) ≥ 0.059 °C/W
(maximum power: 1800 W)
AEC-Q200 conditions: IEC 60115-1/IEC 60068-2-14, Test Na
50 cycles (- 55 °C to + 200 °C)
1000 cycles (- 55 °C to + 200 °C)
AEC-Q200 conditions: IEC 60115-1
2000 h (90/30) P r
AEC-Q200 conditions: IEC 60115-1, 1000 h RH 85 %/85 °C
AEC-Q200 conditions: MIL-STD-202 method 213 condition D
(100 g ’s/6 ms 3.75 m/s)
AEC-Q200 conditions: MIL-STD-202 method 204 condition D
(5 g , 20 min 10/2000 Hz)
AEC-Q200 conditions: IEC 60115-1 (55/200/56)
REQUIREMENTS
± (0.25 % + 0.05 Ω )
± (0.5 % + 0.05 Ω ) for all the ohmic values
± (5 % + 0.05 Ω ) for R < 38 Ω
± (0.5 % + 0.05 Ω ) for R ≥ 38 Ω
± (5 % + 0.05 Ω ) for R < 38 Ω
± (0.5 % + 0.05 Ω ) for R ≥ 38 Ω
± (0.5 % + 0.05 Ω )
± (1 % + 0.05 Ω )
± (1 % + 0.05 Ω )
± (1 % + 0.05 Ω )
RECOMMENDATIONS FOR MOUNTING ONTO A HEATSINK
? Surfaces in contact must be carefully cleaned.
? The heatsink must have an acceptable flatness: From 0.05 mm to 0.1 mm/100 mm.
? Roughness of the heatsink must be around 6.3 μm. In order to improve thermal conductivity, surfaces in contact (ceramic,
heatsink) should be coated with a silicone grease (type Bluesil Past 340 from Blue Star Silicones). Thermal film (type Q-pad II
from Berquist) is also possible, easier and faster to install than grease but with a lower efficiency for the power dissipation.
? The fastening of the resistor to the heatsink is under pressure control of two screws tightened at 2 Nm for full power
availability.
Tightening Torque on Heatsink
LPS 1100
2 Nm
Δ T
[ R th (j - c) ] + [ R th (c - h) ] + [ R th (h - a) ]
Δ T 182
R th (j - c) + R TH (c - h) + R TH (h - a) = ------- = ---------- = 0.214 °C/W
? The following accessories are supplied with each product:
- 2 screws CHC M4 x 25 class 8.8 and 2 M4 contact lock washers for heatsink mounting
- 2 screws TH M4 x 6/6 and 2 M4 contact lock washers for connections. 2 off CHC M4 x 16/16 class 8
CHOICE OF THE HEATSINK AND THE THERMAL INTERFACE
The user must choose the heatsink according to the working conditions of the component (power, room temperature).
Maximum working temperature must not exceed 200 °C. The dissipated power is simply calculated by the following ratio:
P = ---------------------------------------------------------------------------------------------
P: Expressed in W
Δ T: Difference between maximum working temperature and room temperature or fluid cooling temperature.
R th (j - c) : Thermal resistance value measured between resistive layer and outer side of the resistor. It is the thermal
resistance of the component: 0.039 °C/W.
R th (c - h) : Thermal resistance value measured between outer side of the resistor and upper side of the heatsink. This is the
thermal resistance of the interface (grease, thermal pad), and the quality of the fastening device.
R th (h - a) : Thermal resistance of the heatsink.
Example:
R th (c - h) + R th (h - a) for LPS 1100 power dissipation 850 W at + 18 °C fluid temperature.
Δ T ≤ 200 °C - 18 °C = 182 °C
P 850
R th (j - c) = 0.039 °C/W
R th (c - h) + R th (h - a) = 0.214 °C/W - 0.039 °C/W = 0.175 °C/W
Revision: 24-Oct-13
2
Document Number: 50059
For technical questions, contact: sferfixedresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
相关PDF资料 |
PDF描述 |
|---|---|
| LR1000 | LINE CONDITIONER 1000W 4OUT |
| LR1200480D40R | RELAY SSR 40A 480VAC AC OUT PCB |
| LR2000 | 4NEMA & 3IEC-320 OUT LINE COND |
| LR604 | LINE CONDITIONER 600W 3OUT |
| LRC-LRF2010LF-01-R025-F | RES .025 OHM 1W 1% 2010 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LPS1100H4R70FB | 制造商:Vishay Dale 功能描述:LPS 1100 H 4U7 1% BO15 E - Boxed Product (Development Kits) |
| LPS1100H4R70JB | 功能描述:平面电阻器 - 底架安装 1100watts 4.7ohms 5% RoHS:否 制造商:AVX 电阻:100 Ohms 功率额定值:250 W 容差:5 % 电压额定值: 系列: 温度系数:150 PPM / C 工作温度范围:- 55 C to + 150 C 尺寸:9.78 mm W x 24.77 mm L x 4.32 mm H 封装:Bulk |
| LPS1100H7R50JB | 制造商:Vishay Dale 功能描述:LPS 1100 H 7U5 5% BO15 E - Boxed Product (Development Kits) |
| LPS1100H90R0FB | 制造商:Vishay Intertechnologies 功能描述:RESISTOR |
| LPS1100L1500KB | 制造商:Vishay Intertechnologies 功能描述:FIXED RESISTORS SFERNICE / BOX / LPS 1100 L 150U 10% BO15 e |
发布紧急采购，3分钟左右您将得到回复。