- 您现在的位置：买卖IC网 > PDF目录13970 > LT1054IN8 (Linear Technology)IC REG SWITCHED CAP DBL INV 8DIP PDF资料下载
参数资料
| 型号： | LT1054IN8 |
| 厂商： | Linear Technology |
| 文件页数： | 6/16页 |
| 文件大小： | 0K |
| 描述： | IC REG SWITCHED CAP DBL INV 8DIP |
| 标准包装： | 50 |
| 类型： | 切换式电容器（充电泵），倍增器，反相 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调 |
| 输入电压： | 3.5 V ~ 15 V |
| 频率 - 开关： | 25kHz |
| 电流 - 输出： | 100mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
| 供应商设备封装： | 8-PDIP |
LT1054/LT1054L
PIN FUNCTIONS
( V OUT ) β
R X ≤
+
–
V +
I OUT
+
R X
LT1054
C IN
GND
V REF
transistormustbeaddedasshowninFigure1.Thiswill
prevent V OUT (Pin 5) from being pulled above the ground
pin (Pin 3) during start-up. Any small, general purpose
transistor such as 2N2222 or 2N2219 can be used. R X
should be chosen to provide enough base drive to the
external transistor so that it is saturated under nominal
output voltage and maximum output current conditions.
In some cases an N-channel enhancement mode MOSFET
can be used in place of the transistor.
I OUT
V +
I L I Q
LOAD
FB/SHDN
CAP + OSC
LT1054 ? F01
C IN GND V REF
CAP – V OUT
C OUT
Figure 1
V REF (Pin 6): Reference Output. This pin provides a 2.5V
reference point for use in LT1054-based regulator circuits.
The temperature coefficient of the reference voltage has
been adjusted so that the temperature coefficient of the
regulated output voltage is close to zero. This requires the
reference output to have a positive temperature coefficient
as can be seen in the typical performance curves. This
nonzero drift is necessary to offset a drift term inherent
in the internal reference divider and comparator network
tied to the feedback pin. The overall result of these drift
terms is a regulated output which has a slight positive
temperature coefficient at output voltages below 5V and a
slight negative TC at output voltages above 5V. Reference
output current should be limited, for regulator feedback
networks, to approximately 60μA. The reference pin will
draw ≈100μA when shorted to ground and will not af-
fect the internal reference/regulator, so that this pin can
also be used as a pull-up for LT1054 circuits that require
synchronization.
OSC (Pin 7): Oscillator Pin. This pin can be used to raise
or lower the oscillator frequency or to synchronize the
device to an external clock. Internally Pin 7 is connected
to the oscillator timing capacitor (C t ≈ 150pF) which is
alternately charged and discharged by current sources of
±7μA so that the duty cycle is ≈50%. The LT1054 oscillator
is designed to run in the frequency band where switch-
ing losses are minimized. However the frequency can be
raised, lowered, or synchronized to an external system
clock if necessary.
The frequency can be lowered by adding an external
capacitor (C1, Figure 2) from Pin 7 to ground. This will
increase the charge and discharge times which lowers the
oscillator frequency. The frequency can be increased by
adding an external capacitor (C2, Figure 2, in the range
of 5pF to 20pF) from Pin 2 to Pin 7. This capacitor will
couple charge into C T at the switch transitions, which will
shorten the charge and discharge time, raising the oscil-
lator frequency. Synchronization can be accomplished
by adding an external resistive pull-up from Pin 7 to the
reference pin (Pin 6). A 20k pull-up is recommended. An
open collector gate or an NPN transistor can then be used
to drive the oscillator pin at the external clock frequency
as shown in Figure 2. Pulling up Pin 7 to an external volt-
age is not recommended. For circuits that require both
frequency synchronization and regulation, an external
reference can be used as the reference point for the top
of the R1/R2 divider allowing Pin 6 to be used as a pull-
up point for Pin 7.
FB/SHDN V + V IN C2
CAP + OSC
+ LT1054
C1
LT1054 ? F02
CAP – V OUT
C OUT
Figure 2
V + (Pin 8): Input Supply. The LT1054 alternately charges
C IN to the input voltage when C IN is switched in parallel
with the input supply and then transfers charge to C OUT
when C IN is switched in parallel with C OUT . Switching oc-
curs at the oscillator frequency. During the time that C IN
1054lfg
6
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3536IMSE#PBF | IC REG BUCK BST SYNC ADJ 12MSOP |
| LTC3521EUF#PBF | IC REG BUCK BOOST SYNC ADJ 24QFN |
| LT3695EMSE-3.3#PBF | IC REG BUCK 3.3V 1A 16MSOP |
| V110B15C150B2 | CONVERTER MOD DC/DC 15V 150W |
| V110B12E200BG2 | CONVERTER MOD DC/DC 12V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1054IN8#PBF | 功能描述:IC REG SWITCHED CAP DBL INV 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1054IN8#PBF | 制造商:Linear Technology 功能描述:DC/DC Controller IC |
| LT1054IP | 功能描述:电荷泵 Switched-Capacitor Voltage Converter RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| LT1054IP | 制造商:Texas Instruments 功能描述:Voltage Regulator IC Package/Case:8-PDIP |
| LT1054IPE4 | 功能描述:电荷泵 Switched-Capacitor Voltage Converter RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。