- 您现在的位置：买卖IC网 > PDF目录13970 > LT1054IN8 (Linear Technology)IC REG SWITCHED CAP DBL INV 8DIP PDF资料下载
参数资料
| 型号： | LT1054IN8 |
| 厂商： | Linear Technology |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC REG SWITCHED CAP DBL INV 8DIP |
| 标准包装： | 50 |
| 类型： | 切换式电容器（充电泵），倍增器，反相 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调 |
| 输入电压： | 3.5 V ~ 15 V |
| 频率 - 开关： | 25kHz |
| 电流 - 输出： | 100mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
| 供应商设备封装： | 8-PDIP |
LT1054/LT1054L
APPLICATIONS INFORMATION
+
C IN
wheredV=peak-to-peakrippleandf=oscillatorfrequency.
For output capacitors with significant ESR a second term
must be added to account for the voltage step at the switch
transitions. This step is approximately equal to:
(2I OUT )(ESR of C OUT )
Power Dissipation
The power dissipation of any LT1054 circuit must be
limited such that the junction temperature of the device
does not exceed the maximum junction temperature rat-
ings. The total power dissipation must be calculated from
two components, the power loss due to voltage drops
in the switches and the power loss due to drive current
losses. The total power dissipated by the LT1054 can be
calculated from:
P ≈ (V IN – | V OUT | )(I OUT ) + (V IN )(I OUT )(0.2)
where both V IN and V OUT are referred to the ground pin
(Pin?3) of the LT1054. For LT1054 regulator circuits, the
power dissipation will be equivalent to that of a linear
regulator. Due to the limited power handling capability of
the LT1054 packages, the user will have to limit output
current requirements or take steps to dissipate some power
external to the LT1054 for large input/output differentials.
This can be accomplished by placing a resistor in series
with C IN as shown in Figure 6. A portion of the input
voltage will then be dropped across this resistor without
affecting the output regulation. Because switch current is
approximately 2.2 times the output current and the resistor
will cause a voltage drop when C IN is both charging and
discharging, the resistor should be chosen as:
R X = V X /(4.4 I OUT )
V IN
FB/SHDN V +
R X
CAP + OSC
LT1054 R1
GND V REF
R2
CAP – V OUT
C1
V OUT
where:
V X ≈ V IN – [(LT1054 Voltage Loss)(1.3) + | V OUT | ]
and I OUT = maximum required output current. The factor
of 1.3 will allow some operating margin for the LT1054.
For example: assume a 12V to – 5V converter at 100mA
output current. First calculate the power dissipation without
an external resistor:
P = (12V – | – 5V | )(100mA) + (12V)(100mA)(0.2)
P = 700mW + 240mW = 940mW
At θ JA of 130°C/W for a commercial plastic device this
would cause a junction temperature rise of 122°C so that
the device would exceed the maximum junction tempera-
ture at an ambient temperature of 25°C. Now calculate the
power dissipation with an external resistor (R X ). First find
how much voltage can be dropped across R X . The maxi-
mum voltage loss of the LT1054 in the standard regulator
configuration at 100mA output current is 1.6V, so:
V X = 12V – [(1.6V)(1.3) + | – 5V | ] = 4.9V and
R X = 4.9V/(4.4)(100mA) = 11Ω
This resistor will reduce the power dissipated by the
LT1054 by (4.9V)(100mA) = 490mW. The total power dis-
sipated by the LT1054 would then be (940mW – 490mW)
= 450mW. The junction temperature rise would now be
only 58°C. Although commercial devices are guaranteed
to be functional up to a junction temperature of 125°C, the
specifications are only guaranteed up to a junction tem-
perature of 100°C, so ideally you should limit the junction
temperature to 100°C. For the above example this would
mean limiting the ambient temperature to 42°C. Other
steps can be taken to allow higher ambient temperatures.
The thermal resistance numbers for the LT1054 packages
represent worst-case numbers with no heat sinking and
still air. Small clip-on type heat sinks can be used to lower
the thermal resistance of the LT1054 package. In some
systems there may be some available airflow which will
help to lower the thermal resistance. Wide PC board traces
from the LT1054 leads can also help to remove heat from
the device. This is especially true for plastic packages.
C OUT
LT1054 ? F06
Figure 6
1954lfg
9
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3536IMSE#PBF | IC REG BUCK BST SYNC ADJ 12MSOP |
| LTC3521EUF#PBF | IC REG BUCK BOOST SYNC ADJ 24QFN |
| LT3695EMSE-3.3#PBF | IC REG BUCK 3.3V 1A 16MSOP |
| V110B15C150B2 | CONVERTER MOD DC/DC 15V 150W |
| V110B12E200BG2 | CONVERTER MOD DC/DC 12V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1054IN8#PBF | 功能描述:IC REG SWITCHED CAP DBL INV 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1054IN8#PBF | 制造商:Linear Technology 功能描述:DC/DC Controller IC |
| LT1054IP | 功能描述:电荷泵 Switched-Capacitor Voltage Converter RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| LT1054IP | 制造商:Texas Instruments 功能描述:Voltage Regulator IC Package/Case:8-PDIP |
| LT1054IPE4 | 功能描述:电荷泵 Switched-Capacitor Voltage Converter RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。