参数资料
| 型号： | LT1083CP-12 |
| 厂商： | Linear Technology |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 12V 7.5A TO-3P-3 |
| 标准包装： | 30 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 12V |
| 输入电压： | 最高 25V |
| 电压 - 压降（标准）： | 1.3V @ 7.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 7.5A |
| 电流 - 限制（最小）： | 8A |
| 工作温度： | 0°C ~ 150°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-247-3 |
| 供应商设备封装： | TO-247-3 |
| 包装： | 散装 |
LT1083/LT1084/LT1085 Fixed
APPLICATIO S I FOR ATIO
folded back as input-to-output voltage increases. This
negative resistance can react with capacitors or inductors
on the input to cause oscillations during current limiting.
Depending on the value of series resistance, the overall
circuitry may end up unstable. Since this is a system
problem, it is not necessarily easy to solve; however it
does not cause any problems with the IC regulator and can
usually be ignored.
Protection Diodes
In normal operation the LT1083 family does not need any
protection diodes, The internal diode between the input
and the output pins of the LT1083 family can handle
microsecond surge currents of 50A to 100A. Even with
large output capacitances it is very difficult to get those
values of surge current in normal operation. Only with high
value output capacitors, such as 1000 μ F to 5000 μ F and
with the input pin instantaneously shorted to ground, can
damage occur. A crowbar circuit at the input of the LT1083
can generate those kinds of currents and a diode from
output-to-input is then recommended. Normal power sup-
ply cycling or even plugging and unplugging in the system
will not generate currents large enough to do any damage.
D1
1N4002
up into very heavy loads. During the start-up, as the input
voltage is rising, the input-to-output voltage differential
remains small allowing the regulator to supply large
output currents. With high input voltage a problem can
occur wherein removal of an output short will not allow the
output voltage to recover. Older regulators such as the
7800 series, also exhibited this phenomenon so it is not
unique to the LT1083.
The problem occurs with a heavy output load when the
input voltage is high and the output voltage is low, such as
immediately after a removal of a short. The load line for
such a load may intersect the output current curve at two
points. If this happens there are two stable output operat-
ing points for the regulator. With this double intersection
the power supply may need to be cycled down to zero and
brought up again to make the output recover.
Ripple Rejection
In applications that require improved ripple rejection the
LT1083 series adjustable regulators should be used. With
LT1083 series adjustable regulators the addition of a
bypass capacitor from the adjust pin to ground will reduce
output ripple by the ratio of V OUT /1.25V. See LT1083
series adjustable regulator data sheet.
(OPTIONAL)
Load Regulation
V IN
IN
LT1083
ADJ
OUT
+
V OUT
C OUT
150 μ F
Because the LT1083 is a three-terminal device, it is not
possible to provide true remote load sensing. Load regu-
lation will not be limited by the resistance of the wire
connecting the regulator to the load. The data sheet
1083/4/5 AI01
Overload Recovery
Like any of the IC power regulators, the LT1083 has safe
area protection. The safe area protection decreases the
current limit as input-to-output voltage increases and
keeps the power transistor inside a safe operating region
for all values of input-to-output voltage. The LT1083
protection is designed to provide some output current at
all values of input-to-output voltage up to the device
breakdown.
When power is first turned on, as the input voltage rises,
the output follows the input, allowing the regulator to start
specification for the load regulation is measured at the
bottom of the package. Negative side sensing is a true
Kelvin connection, with the ground pin of the device
returned to the negative side of the load.
Thermal Considerations
The LT1083 series of regulators have internal power and
thermal limiting circuitry designed to protect the device
under overload conditions. For continuous normal load
conditions however, maximum junction temperature rat-
ings must not be exceeded. It is important to give careful
consideration to all sources of thermal resistance from
junction to ambient. This includes junction-to-case,
1083ffd
8
相关PDF资料 |
PDF描述 |
|---|---|
| LT3032MPDE#TRPBF | IC REG LDO ADJ .15A 14-DFN |
| ACM36DTBH | CONN EDGECARD 72POS R/A .156 SLD |
| ACM36DTBD | CONN EDGECARD 72POS R/A .156 SLD |
| HA4344BCBZ96 | IC SWITCH CROSS VIDEO 4:1 16SOIC |
| LFEC15E-4FN484I | IC FPGA 15.3KLUTS 484FPBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1083CP-12#PBF | 功能描述:IC REG LDO 12V 7.5A TO-3P-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
| LT1083CP-12PBF | 制造商:Linear Technology 功能描述:7500mA,12V,LDO Voltage Reg.,LT1083CP-12 |
| LT1083CP5 | 制造商:Linear Technology 功能描述: |
| LT1083CP-5 | 功能描述:IC REG LDO 5V 7.5A TO-3P-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
| LT1083CP-5#PBF | 功能描述:IC REG LDO 5V 7.5A TO-3P-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
发布紧急采购，3分钟左右您将得到回复。