- 您现在的位置：买卖IC网 > PDF目录14064 > LT1108CS8-5#TR (Linear Technology)IC REG BUCK BST INV 5V .4A 8SOIC PDF资料下载
参数资料
| 型号： | LT1108CS8-5#TR |
| 厂商： | Linear Technology |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BST INV 5V .4A 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 降压（降压），升压（升压），反相 |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 2 V ~ 30 V |
| 频率 - 开关： | 19kHz |
| 电流 - 输出： | 400mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-SOIC |
LT1108
A PPLICATI
S I FOR ATIO
INDUCTOR SELECTION
General
where V D is the diode drop (0.5V for a 1N5818 Schottky).
Energy required by the inductor per cycle must be equal or
greater than
A DC/DC converter operates by storing energy as mag-
netic flux in an inductor core, and then switching this
energy into the load. Since it is flux, not charge, that is
P L / f OSC
in order for the converter to regulate the output.
( 02 )
stored, the output voltage can be higher, lower, or oppo-
site in polarity to the input voltage by choosing an appro-
priate switching topology.
When the switch is closed, current in the inductor builds
according to
I L ( t ) = IN ? 1 – e L ?
To operate as an efficient energy transfer element, the
inductor must fulfill three requirements. First, the induc-
tance must be low enough for the inductor to store adequate
V ? –R't ?
R ' ? ?
( 03 )
energy under the worst case condition of minimum input
voltage and switch-ON time. The inductance must also be
high enough so maximum current ratings of the LT1108
and inductor are not exceeded at the other worst case
condition of maximum input voltage and ON-time.
where R' is the sum of the switch equivalent resistance
(0.8 ? typical at 25 ° C) and the inductor DC resistance.
When the drop across the switch is small compared to V IN ,
the simple lossless equation
()
I L t = IN t
Additionally, the inductor core must be able to store the
required flux; i.e., it must not saturate. At power levels
V
L
( 04 )
generally encountered with LT1108 based designs, small
surface mount ferrite core units with saturation current
ratings in the 300mA to 1A range and DCR less than 0.4 ?
(depending on application) are adequate.
Lastly, the inductor must have sufficiently low DC resis-
tance so excessive power is not lost as heat in the windings.
An additional consideration is Electro-Magnetic Interfer-
can be used. These equations assume that at t = 0,
inductor current is zero. This situation is called “discontinu-
ous mode operation” in switching regulator parlance.
Setting “t” to the switch-ON time from the LT1108 specifi-
cation table (typically 36 μ s) will yield I PEAK for a specific “L”
and V IN . Once I PEAK is known, energy in the inductor at the
end of the switch-ON time can be calculated as
LI PEAK
ence (EMI). Toroid and pot core type inductors are recom-
mended in applications where EMI must be kept to a
minimum; for example, where there are sensitive analog
E L =
1
2
2
( 05 )
P L = ( V OUT + V D – V IN MIN )( I OUT )
P L = ( 12 V + 0 . 5 V – 2 V )( 30 mA ) = 315 mW
circuitry or transducers nearby. Rod core types are a less
expensive choice where EMI is not a problem. Minimum
and maximum input voltage, output voltage and output
current must be established before an inductor can be
selected.
Step-Up Converter
In a step-up, or boost converter (Figure 1), power generated
by the inductor makes up the difference between input and
output. Power required from the inductor is determined by
( 01 )
6
E L must be greater than P L /f OSC for the converter to deliver
the required power. For best efficiency I PEAK should be kept
to 1A or less. Higher switch currents will cause excessive
drop across the switch resulting in reduced efficiency. In
general, switch current should be held to as low a value as
possible in order to keep switch, diode and inductor losses
at a minimum.
As an example, suppose 12V at 30mA is to be generated
from a 2V to 3V input. Recalling equation (01),
( 06 )
相关PDF资料 |
PDF描述 |
|---|---|
| RBM10DTAN-S664 | CONN EDGECARD 20POS R/A .156 SLD |
| 50MS70.33MEFCTZ4X7 | CAP ALUM 0.33UF 50V 20% RADIAL |
| RBM10DTAD-S664 | CONN EDGECARD 20POS R/A .156 SLD |
| EBM22DTAN-S664 | CONN EDGECARD 44POS R/A .156 SLD |
| VE-JV1-CZ-F1 | CONVERTER MOD DC/DC 12V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1108CS8PBF | 制造商:Linear Technology 功能描述:DC/DC Converter Adj Micropower 2-30V SO8 |
| LT1109 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Low Cost DC/DC Converter Adjustable and Fixed 5V, 12V |
| LT1109-12 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Low Cost DC/DC Converter Adjustable and Fixed 5V, 12V |
| LT1109-5 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Low Cost DC/DC Converter Adjustable and Fixed 5V, 12V |
| LT1109A | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower DC/DC Converter Flash Memory VPP Generator Adjustable and Fixed 5V, 12V |
发布紧急采购，3分钟左右您将得到回复。