- 您现在的位置：买卖IC网 > PDF目录14819 > LT1305CS8#PBF (Linear Technology)IC REG BOOST 5V 0.4A 8SOIC PDF资料下载
参数资料
| 型号： | LT1305CS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST 5V 0.4A 8SOIC |
| 标准包装： | 100 |
| 类型： | 升压（升压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 1.8 V ~ 10 V |
| PWM 型： | Burst Mode? |
| 电流 - 输出： | 400mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
| 产品目录页面： | 1326 (CN2011-ZH PDF) |
LT1305
OPERATIO N
If switch current reaches 2A, causing C2 to trip, switch on
time is reduced and off time increases slightly. This allows
continuous operation during bursts. C2 monitors the
voltage across 3 ? resistor R1 which is directly related to
the switch current. Q2’s collector current is set by the
emitter-area ratio to 0.6% of Q1’s collector current. When
R1’s voltage drop exceeds 36mV, corresponding to 2A
switch current, C2’s output goes high, truncating the on
time portion of the oscillator cycle and increasing off time
to about 2 μ s. Response time of C2, which determines
minimum on time, is approximately 300ns.
Low-Battery Detector
The low-battery detector is enabled when SHDN is low and
disabled when SHDN is high. The comparator has no
hysteresis built in, but hysteresis can be added by
connecting a high-value resistor from LBI to LBO as
shown in Figure 3. The internal reference can be accessed
Inductor Selection
Inductors used with the LT1305 must fulfill two require-
ments. First, the inductor must be able to handle current
of 2A to 2.5A without runaway saturation. Rod or drum
core units usually saturate gradually and it is acceptable to
exceed manufacturer’s published saturation current by
20% or so. Second, the unit must have low DCR, under
0.05 ? so that copper loss is kept low and excess heating
is avoided. Inductance value is not critical. Generally, for
low voltage inputs below 3V a 10 μ H inductor is recom-
mended (such as Coilcraft DO3316-103). For inputs above
4V to 5V use a 22 μ H unit (such as Coilcraft DO3316-223).
Switching frequency can reach up to 300kHz so the core
material should be able to operate at high frequency
without excessive core loss. Ferrite or molypermalloy
cores are a better choice than powdered iron. If EMI is a
concern, a toroidal inductor is suggested, such as
Coiltronics CTX20-4.
via the comparator as shown in Figure 4.
Capacitor Selection
V BAT
LT1305
5V
Output and input capacitors should have low ESR for best
R1
R2
49.9k
1.24V
LBI
–
+
LBO
R4
47k
performance. Inexpensive aluminum electrolytics some-
times have ESR above 1 ? , even for relatively large values
such as 100 μ F, 16V units. Since the LT1305 has a 2A
current limit, 2V of ripple voltage would result with such a
capacitor at the output. Keep ESR below 0.05 ? to 0.1 ? for
1%
R1 = (V TRIP –1.24V) (43.5k)
HYSTERESIS ≈ 30mV
R3
2M
LT1305 ? F03
reasonable ripple voltage. Tantalum capacitors such as
AVX TPS series or Sprague 593D have low ESR and are
surface mount components. For lowest ESR, use Sanyo
Figure 3. R3 Adds Hysteresis to Low-Battery Detector
V IN
OS-CON units (OS-CON is also available from Vishay).
These capacitors have superior ESR, small size and per-
form well at cold temperatures.
2N3906
100k
V IN
LBO
LT1305
Diode Selection
A 2A Schottky diode such as Motorola MBRS130LT3 is a
good choice for the rectifier diode. A 1N5821 or
V REF
OUTPUT
+
R2
2.2 μ F
R1
LBI
GND
MBRS130T3 are suitable as well. Do not use “general
purpose” diodes such as 1N4001. They are much too slow
for use in switching regulator applications.
( )
V REF = 1.24V 1 + R2
R1
V IN ≥ V REF + 200mV
R1 + R2 ≈ 33k
LT1305 ? F04
Figure 4. Accessing Internal Reference
6
相关PDF资料 |
PDF描述 |
|---|---|
| LT1054CSW#PBF | IC REG MULTI CONFIG ADJ 16SOIC |
| VI-JVN-EY-F4 | CONVERTER MOD DC/DC 18.5V 50W |
| LT3685EMSE#PBF | IC REG BUCK ADJ 2A 10MSOP |
| LTC3388EMSE-1#PBF | IC REG BUCK SYNC 50MA 10MSOP |
| LTC3523EUD#PBF | IC REG BUCK BOOST SYNC ADJ 16QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1306 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous, Fixed Frequency Step-Up DC/DC Converter |
| LT1306ES8 | 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1306ES8#PBF | 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1306ES8#TR | 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1306ES8#TRPBF | 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。