- 您现在的位置：买卖IC网 > PDF目录13872 > LT1374IS8-SYNC (Linear Technology)IC REG BUCK ADJ 4.5A 8SOIC PDF资料下载
参数资料
| 型号： | LT1374IS8-SYNC |
| 厂商： | Linear Technology |
| 文件页数： | 10/32页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 4.5A 8SOIC |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.42 V ~ 21.5 V |
| 输入电压： | 5 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 4.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LT1374
APPLICATIO N S I N FOR M ATIO N
MAXIMUM OUTPUT LOAD CURRENT
Maximum load current for a buck converter is limited by
the maximum switch current rating (I P ) of the LT1374.
This current rating is 4.5A up to 50% duty cycle (DC),
decreasing to 3.7A at 80% duty cycle. This is shown
graphically in Typical Performance Characteristics and as
shown in the formula below:
I P = 4.5A for DC ≤ 50%
I P = 3.21 + 5.95(DC) – 6.75(DC) 2 for 50% < DC < 90%
DC = Duty cycle = V OUT /V IN
Example: with V OUT = 5V, V IN = 8V; DC = 5/8 = 0.625, and;
I SW(MAX) = 3.21 + 5.95(0.625) – 6.75(0.625) 2 = 4.3A
Current rating decreases with duty cycle because the
LT1374 has internal slope compensation to prevent current
mode subharmonic switching. For more details, read Ap-
plication Note 19. The LT1374 is a little unusual in this regard
because it has nonlinear slope compensation which gives
better compensation with less reduction in current limit.
Maximum load current would be equal to maximum
switch current for an infinitely large inductor, but with
finite inductor size, maximum load current is reduced by
one-half peak-to-peak inductor current. The following
formula assumes continuous mode operation, implying
that the term on the right is less than one-half of I P .
I OUT(MAX) =
Continuous Mode
For the conditions above and L = 3.3 μ H,
At V IN = 15V, duty cycle is 33%, so I P is just equal to a fixed
4.5A, and I OUT(MAX) is equal to:
Note that there is less load current available at the higher
input voltage because inductor ripple current increases.
This is not always the case. Certain combinations of
inductor value and input voltage range may yield lower
available load current at the lowest input voltage due to
reduced peak switch current at high duty cycles. If load
current is close to the maximum available, please check
maximum available current at both input voltage
extremes. To calculate actual peak switch current with a
given set of conditions, use:
For lighter loads where discontinuous operation can be
used, maximum load current is equal to:
I OUT(MAX) =
Discontinuous mode
Example: with L = 1.2 μ H, V OUT = 5V, and V IN(MAX ) = 15V,
The main reason for using such a tiny inductor is that it is
physically very small, but keep in mind that peak-to-peak
inductor current will be very high. This will increase output
ripple voltage. If the output capacitor has to be made larger
to reduce ripple voltage, the overall circuit could actually
wind up larger.
CHOOSING THE INDUCTOR AND OUTPUT CAPACITOR
For most applications the output inductor will fall in the
range of 3 μ H to 20 μ H. Lower values are chosen to reduce
physical size of the inductor. Higher values allow more
output current because they reduce peak current seen by
the LT1374 switch, which has a 4.5A limit. Higher values
also reduce output ripple voltage, and reduce core loss.
Graphs in the Typical Performance Characteristics section
show maximum output load current versus inductor size
and input voltage. A second graph shows core loss versus
inductor size for various core materials.
1374fd
10
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JNY-EZ-F2 | CONVERTER MOD DC/DC 3.3V 16.5W |
| VI-JNY-EZ-F1 | CONVERTER MOD DC/DC 3.3V 16.5W |
| VI-J3P-EZ-F4 | CONVERTER MOD DC/DC 13.8V 25W |
| L06031R8CGWTR | INDUCTOR THIN FILM 1.8NH 0603 |
| L06031R5CGWTR | INDUCTOR THIN FILM 1.5NH 0603 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1374IS8-SYNC#PBF | 功能描述:IC REG BUCK ADJ 4.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1374IS8-SYNC#TR | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 5V to 25V 8-Pin SOIC N T/R |
| LT1374IT7 | 功能描述:IC REG BUCK ADJ 4.5A TO220-7 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1374IT7#PBF | 功能描述:IC REG BUCK ADJ 4.5A TO220-7 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1374IT7-5 | 功能描述:IC REG BUCK 5V 4.5A TO220-7 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。