- 您现在的位置：买卖IC网 > PDF目录13872 > LT1374IS8-SYNC (Linear Technology)IC REG BUCK ADJ 4.5A 8SOIC PDF资料下载
参数资料
| 型号： | LT1374IS8-SYNC |
| 厂商： | Linear Technology |
| 文件页数： | 23/32页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 4.5A 8SOIC |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.42 V ~ 21.5 V |
| 输入电压： | 5 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 4.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LT1374
APPLICATIO N S I N FOR M ATIO N
What About a Resistor in the Compensation Network?
It is common practice in switching regulator design to
add a “zero” to the error amplifier compensation to
increase loop phase margin. This zero is created in the
external network in the form of a resistor (R C ) in series
with the compensation capacitor. Increasing the size of
this resistor generally creates better and better loop
stability, but there are two limitations on its value. First,
the combination of output capacitor ESR and a large
value for R C may cause loop gain to stop rolling off
altogether, creating a gain margin problem. An approxi-
G MA = Error amplifier transconductance (2000 μ Mho)
If a computer simulation of the LT1374 showed that a
series compensation resistor of 3k gave best overall loop
response, with adequate gain margin, the resulting V C pin
ripple voltage with V IN = 10V, V OUT = 5V, ESR = 0.1 ? ,
L = 10 μ H, would be:
mate formula for R C where gain margin falls to zero is:
This ripple voltage is high enough to possibly create
G MP = Transconductance of power stage = 5.3A/V
G MA = Error amplifier transconductance = 2(10 –3 )
ESR = Output capacitor ESR
2.42 = Reference voltage
With V OUT = 5V and ESR = 0.03 ? , a value of 6.5k for R C
would yield zero gain margin, so this represents an upper
limit. There is a second limitation however which has
nothing to do with theoretical small signal dynamics.
This resistor sets high frequency gain of the error ampli-
fier, including the gain at the switching frequency. If
switching frequency gain is high enough, output ripple
voltage will appear at the V C pin with enough amplitude
to muck up proper operation of the regulator. In the
marginal case, subharmonic switching occurs, as evi-
denced by alternating pulse widths seen at the switch
node. In more severe cases, the regulator squeals or
hisses audibly even though the output voltage is still
roughly correct. None of this will show on a theoretical
Bode plot because Bode is an amplitude insensitive
analysis. Tests have shown that if ripple voltage on the V C
is held to less than 100mV P-P , the LT1374 will be well
behaved. The formula below will give an estimate of V C
ripple voltage when R C is added to the loop, assuming
that R C is large compared to the reactance of C C at
500kHz.
subharmonic switching. In most situations a compromise
value (< 2k in this case) for the resistor gives acceptable
phase margin and no subharmonic problems. In other
cases, the resistor may have to be larger to get acceptable
phase response, and some means must be used to control
ripple voltage at the V C pin. The suggested way to do this
is to add a capacitor (C F ) in parallel with the R C /C C network
on the V C pin. Pole frequency for this capacitor is typically
set at one-fifth of switching frequency so that it provides
significant attenuation of switching ripple, but does not
add unacceptable phase shift at loop unity-gain frequency.
With R C = 3k,
How Do I Test Loop Stability?
The “standard” compensation for LT1374 is a 1.5nF
capacitor for C C , with R C = 0. While this compensation will
work for most applications, the “optimum” value for loop
compensation components depends, to various extent, on
parameters which are not well controlled. These include
inductor value ( ± 30% due to production tolerance, load
1374fd
23
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JNY-EZ-F2 | CONVERTER MOD DC/DC 3.3V 16.5W |
| VI-JNY-EZ-F1 | CONVERTER MOD DC/DC 3.3V 16.5W |
| VI-J3P-EZ-F4 | CONVERTER MOD DC/DC 13.8V 25W |
| L06031R8CGWTR | INDUCTOR THIN FILM 1.8NH 0603 |
| L06031R5CGWTR | INDUCTOR THIN FILM 1.5NH 0603 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1374IS8-SYNC#PBF | 功能描述:IC REG BUCK ADJ 4.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1374IS8-SYNC#TR | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 5V to 25V 8-Pin SOIC N T/R |
| LT1374IT7 | 功能描述:IC REG BUCK ADJ 4.5A TO220-7 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1374IT7#PBF | 功能描述:IC REG BUCK ADJ 4.5A TO220-7 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1374IT7-5 | 功能描述:IC REG BUCK 5V 4.5A TO220-7 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。