- 您现在的位置：买卖IC网 > PDF目录44981 > LT1507IS8-3.3#TR (LINEAR TECHNOLOGY CORP) 3 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO8 PDF资料下载
参数资料
| 型号： | LT1507IS8-3.3#TR |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 3 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封装： | 0.150 INCH, PLASTIC, SO-8 |
| 文件页数： | 5/20页 |
| 文件大小： | 291K |
| 代理商： | LT1507IS8-3.3#TR |
13
LT1507
APPLICATIONS INFORMATION
WU
U
This is safe for short periods of time, but it would be
prudent to check with the diode manufacturer if continu-
ous operation under these conditions must be tolerated.
BOOST PIN CONSIDERATIONS
For most applications, the boost components are a 0.22
F
capacitor and an MBR0520 or BAT85 Schottky diode. This
capacitor value is twice that suggested for the LT1376
because the lower voltages commonly found in LT1507
applications may require lower ripple voltage across the
capacitor to ensure adequate boost voltage under worst-
case conditions. Efficiency is not affected by the capacitor
value, but the capacitor should have an ESR of less than
2
toensurethatitcanberechargedfullyundertheworst-
case condition of minimum input voltage. Almost any type
of film or ceramic capacitor will work fine.
Figure 3. Suggested Layout
The anode of the diode can be connected to the regulated
output voltage or the unregulated input voltage. The
“boost voltage” generated across the boost capacitor is
then nearly identical to the anode voltage. The input
connection minimizes start-up problems and gives plenty
of boost voltage, but efficiency is slightly lower, especially
with input voltages above 10V. For 5V to 3.3V operation,
or any output voltage less than 3.3V, the diode should be
connected to the input. With input voltage more than 3V
above the output and an output voltage of at least 3.3V the
output connection will give better efficiency. Use the
BAT85 Schottky diode for 3.3V applications where the
anode is connected to the output.
LAYOUT CONSIDERATIONS
Suggested layout for the LT1507 is shown in Figure 3. The
main concern for layout is to minimize the length of the
INPUT
C2
C3
D2
CC
RC
R1
SYNC
C1
LT1507 F03
D1
L1
R2
BOOST
IN
SW
SHDN
VC
FB
GND
SYNC
OUTPUT
MINIMIZE AREA OF
CONNECTIONS TO THE
SWITCH NODE AND
BOOST NODE, BUT OBSERVE
CURRENT DENSITY LIMITATIONS
IN PATH TO L1
KEEP INPUT CAPACITOR
AND CATCH DIODE CLOSE
TO REGULATOR AND
TERMINATE THEM
TO SAME POINT
CONNECT OUTPUT CAPACITOR
DIRECTLY TO HEAVY GROUND
TAKE OUTPUT DIRECTLY FROM END OF OUTPUT
CAPACITOR TO AVOID PARASITIC RESISTANCE
AND INDUCTANCE (KELVIN CONNECTION)
GROUND RING NEED
NOT BE AS SHOWN.
(NORMALLY EXISTS AS
INTERNAL PLANE)
CF AND RC ARE OPTIONAL.
SEE FREQUENCY
COMPENSATION
CF
TERMINATE GND PIN
DIRECTLY TO GROUND
PLANE WITH VIA TO
MINIMIZE EMI. (MINIMIZE
DISTANCE TO INPUT
CAPACITOR C3). CONNECT
FEEDBACK RESISTORS AND
COMPENSATION
COMPONENTS DIRECTLY
TO GROUND PLANE OR TO
SWITCHER GND PIN.
相关PDF资料 |
PDF描述 |
|---|---|
| LT1509IS | 2 A POWER FACTOR CONTROLLER WITH POST REGULATOR, PDSO20 |
| LT1509CS | 2 A POWER FACTOR CONTROLLER WITH POST REGULATOR, PDSO20 |
| LT1513CT7 | 5.4 A BATTERY CHARGE CONTROLLER, 580 kHz SWITCHING FREQ-MAX, PZFM7 |
| LT1576IS8#TR | 3.5 A SWITCHING REGULATOR, 240 kHz SWITCHING FREQ-MAX, PDSO8 |
| LT1634CMS8-2.5#PBF | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1508 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power Factor and PWM Controller(Voltage Mode) |
| LT1508C | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power Factor and PWM Controller(Voltage Mode) |
| LT1508CN | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power Factor and PWM Controller(Voltage Mode) |
| LT1508CSW | 功能描述:IC PWM/POWER FACTOR CNTRLR20SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - PFC（功率因数修正） 系列:- 产品培训模块:GreenChip Synchronous Rectification Control Family of ICs 标准包装:1 系列:- 模式:间歇导电（DCM） 频率 - 开关:- 电流 - 启动:- 电源电压:8.6 V ~ 38 V 工作温度:-20°C ~ 150°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:Digi-Reel® 其它名称:568-5348-6 |
| LT1508I | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power Factor and PWM Controller(Voltage Mode) |
发布紧急采购，3分钟左右您将得到回复。