- 您现在的位置：买卖IC网 > PDF目录98002 > LT1508ISW#TR (LINEAR TECHNOLOGY CORP) POWER FACTOR CONTROLLER WITH POST REGULATOR, 115 kHz SWITCHING FREQ-MAX, PDSO20 PDF资料下载
参数资料
| 型号： | LT1508ISW#TR |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | POWER FACTOR CONTROLLER WITH POST REGULATOR, 115 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封装： | 0.300 INCH, PLASTIC, SO-20 |
| 文件页数： | 2/16页 |
| 文件大小： | 300K |
| 代理商： | LT1508ISW#TR |
10
LT1508
line current reaches the secondary limit, the comparator
takes over control and hysteresis may occur causing
audible noise.
Overvoltage Protection (PFC Section)
Because of the slow loop response necessary for power
factor correction, output overshoot can occur following a
sudden load reduction or removal. To protect downstream
components, the LT1508 provides an overvoltage com-
parator which senses the output voltage and quickly
reduces the line current demand. Referring back to Figure
1, VOUT is 382V and during normal operation, since no
current flows in R3, 7.5V appears at both the VSENSE and
OVP pins. When VOUT overshoots its preset value, the
overcurrent from R1 will flow through R2 as well as R3.
The voltage amplifier feedback will keep VSENSE at 7.5V.
Therefore, the equivalent AC resistance seen by the OVP
pin is R2 in parallel with R3 or 10k. With these values and
the overvoltage comparator trip level internally set at
1.05VREF, the comparator trips when VOUT overshoots
10%. Overvoltage trip level is given by:
R2 + R3
R3
(%)VOUT = 5%
()
For additional protection, the OVP pin can be connected
to VOUT through an independent resistor divider (see
Figure 7). This ensures overvoltage protection during
safety agency abnormal testing conditions, such as
opening R1 or shorting R2.
The output of the multiplier looks like a high impedance
current source. In the current loop, offset line current is
determined by multiplier offset current and input offset
voltage of the current error amplifier. A – 4mV current
amplifier VOS translates to 27mA line current and 6.7W
input power for 250VAC line if a 0.15
sense resistor is
used. Under a no-load condition or when the load power
is less than the offset output power, the offset line current
could slowly charge the output to an overvoltage level.
This is because the best the overvoltage comparator can
do is to reduce the multiplier output current to zero.
Unfortunately, this does not guarantee zero output current
if the current amplifier has offset. To regulate VOUT under
–
+
R4
1.05M
R5
20k
R1
1M
R2
20k
VSENSE
OVP
ERROR
AMP
–
+
OVERVOLTAGE
COMPARATOR
0.047
F
VOUT
0.47
F
330k
VAOUT
1.05VREF
VOUT = 382V
OVERVOLTAGE = 420V
1508 F07
LT1508
Figure 7
this condition, the amplifier M1 (see Block Diagram)
becomes active. When VAOUT reduces to 2.2V, M1 sup-
plies up to 7
A of current to the resistor at the ISENSE pin
in order to cancel a negative VOS and keep VOUT error to
within 2V.
Undervoltage Lockouts and Soft Start
The LT1508 turns on when VCC reaches 16V and remains
on until VCC falls below 10V, whereupon the chip enters the
lockout state. In the lockout state, the oscillator is off and
the VREF and gate driver pins remain low. A capacitor from
SS1 to GND1 determines the ramp-up time of the PFC
section. SS1 is released from a zero when VCC rises above
the lockout threshold. Once released, an internal 14
A
current source ramps the voltage error amplifier’s refer-
ence voltage to 7.5V. SS1 voltage then continues beyond
7.5V. A second capacitor from SS2 to GND1 determines
the start-up time from the PWM section. A PWMOK
comparator (see Block Diagram) holds SS2 low until the
OVP pin reaches 7V. This corresponds to the PFC output
voltage reaching approximately 93% of its preset voltage.
SS2 is diode coupled to the PMW comparator which is
connected to the VC pin by a second diode. Holding SS2
low at any time will disable PWM output. Once released,
the 14
A current source ramps the PWM comparator
APPLICATIONS INFORMATION
WU
U
相关PDF资料 |
PDF描述 |
|---|---|
| LT1513IT7-2#PBF | 5.4 A BATTERY CHARGE CONTROLLER, 580 kHz SWITCHING FREQ-MAX, PSFM7 |
| LT1513IR-2#PBF | 5.4 A BATTERY CHARGE CONTROLLER, 580 kHz SWITCHING FREQ-MAX, PSSO7 |
| LT1640LCS8#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LT1932ES6#PBF | 0.78 A SWITCHING REGULATOR, 1600 kHz SWITCHING FREQ-MAX, PDSO6 |
| LT1932ES6#TR | 0.78 A SWITCHING REGULATOR, 1600 kHz SWITCHING FREQ-MAX, PDSO6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1509 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power Factor and PWM Controller |
| LT15090 | 制造商:Cooper Crouse-Hinds 功能描述: 制造商:CROUSE-HINDS/COOPER 功能描述: |
| LT1509CN | 功能描述:IC PFC CTRLR AVERAGE CURR 20DIP RoHS:否 类别:集成电路 (IC) >> PMIC - PFC（功率因数修正） 系列:- 产品培训模块:GreenChip Synchronous Rectification Control Family of ICs 标准包装:1 系列:- 模式:间歇导电（DCM） 频率 - 开关:- 电流 - 启动:- 电源电压:8.6 V ~ 38 V 工作温度:-20°C ~ 150°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:Digi-Reel® 其它名称:568-5348-6 |
| LT1509CN#PBF | 功能描述:IC PFC CTRLR AVERAGE CURR 20DIP RoHS:是 类别:集成电路 (IC) >> PMIC - PFC（功率因数修正） 系列:- 产品培训模块:GreenChip Synchronous Rectification Control Family of ICs 标准包装:1 系列:- 模式:间歇导电（DCM） 频率 - 开关:- 电流 - 启动:- 电源电压:8.6 V ~ 38 V 工作温度:-20°C ~ 150°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:Digi-Reel® 其它名称:568-5348-6 |
| LT1509CSW | 功能描述:IC PFC CTRLR AVERAGE CURR 20SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - PFC（功率因数修正） 系列:- 产品培训模块:GreenChip Synchronous Rectification Control Family of ICs 标准包装:1 系列:- 模式:间歇导电（DCM） 频率 - 开关:- 电流 - 启动:- 电源电压:8.6 V ~ 38 V 工作温度:-20°C ~ 150°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:Digi-Reel® 其它名称:568-5348-6 |
发布紧急采购，3分钟左右您将得到回复。