- 您现在的位置：买卖IC网 > PDF目录377712 > LT1671CS8 (LINEAR TECHNOLOGY CORP) 60ns, Low Power, Single Supply, Ground-Sensing Comparator PDF资料下载
参数资料
| 型号： | LT1671CS8 |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 运动控制电子 |
| 英文描述： | 60ns, Low Power, Single Supply, Ground-Sensing Comparator |
| 中文描述： | COMPARATOR, 4000 uV OFFSET-MAX, 85 ns RESPONSE TIME, PDSO8 |
| 封装： | 0.150 INCH, PLASTIC, SOP-8 |
| 文件页数： | 8/12页 |
| 文件大小： | 199K |
| 代理商： | LT1671CS8 |
8
LT1671
APPLICATIO
S I
FOR
ATIO
U
W
U
U
circuit is the lack of feedthrough from the generator to the
comparator input. This prevents overshoot on the com-
parator input, which would give a false fast reading on
comparator response time.
To adjust the circuit for exactly 5mV overdrive, V1 is
adjusted so that the LT1671 output under test settles to
1.4V (in the linear region). Then V1 is changed by –1V to
set overdrive to 5mV.
High Speed Design Techniques
A substantial amount of design effort has made the LT1671
relatively easy to use. It is much less prone to oscillation
than some slower comparators, even with slow input
signals. However, as with any high speed comparator,
there are a number of problems which may arise because
of PC board layout and design. The most common prob-
lem involves power supply bypassing. Bypassing is nec-
essary to maintain low supply impedance. DC resistance
and inductance in supply wires and PC traces can quickly
build up to unacceptable levels. This allows the supply line
to move with changing internal current levels of the
connected devices. This will almost always result in
improper operation. In addition, adjacent devices con-
nected through an unbypassed supply can interact with
each other through the finite supply impedances. Bypass
capacitors furnish a simple solution to this problem by
providing a local reservoir of energy at the device, keeping
supply impedances low.
Bypass capacitors should be as close as possible to the
LT1671. A good high frequency capacitor such as a 0.1
μ
F
ceramic is recommended, in parallel with a larger capaci-
tor such as a 4.7
μ
F tantalum.
Poor trace routes and high source impedances are also
common sources of problems. Be sure to keep trace
lengths as short as possible, and avoid running any output
trace adjacent to an input trace to prevent unnecessary
coupling. If output traces are longer than a few inches, be
sure to terminate them with a resistor to eliminate any
reflections that may occur. Resistor values are typically
250
to 400
. Also, be sure to keep source impedances
as low as possible, preferably 1k
or less.
About Level Shifts
The LT1671’s logic output will interface with many cir-
cuits directly. Many applications, however, require some
form of level shifting of the output swing. With LT1671-
based circuits this is not trivial because it is desirable to
maintain very low delay in the level shifting stage. When
designing level shifters, keep in mind that the TTL output
of the LT1671 is a sink-source pair (Figure 3) with good
ability to drive capacitance (such as feedforward capaci-
tors). Figure 4 shows a noninverting voltage gain stage
with a 15V output. When the LT1671 switches, the base-
emitter voltages at the 2N2369 reverse, causing it to
switch very quickly. The 2N3866 emitter-follower gives a
low impedance output and the Schottky diode aids cur-
rent sink capability.
–
+
LT1671
1671 F02
FET PROBE
FET PROBE
* TOTAL LEAD LENGTH INCLUDING DEVICE PIN.
SOCKET AND CAPACITOR LEADS SHOULD BE
LESS THAN 0.5 IN. USE GROUND PLANE
** (V
OS
+ OVERDRIVE)/200
25
25
5V
0.01
μ
F*
0.01
μ
F
10k
50
V1**
2N3866
0V
–3V
–5V
–5V
50
PULSE
IN
750
400
0.1
μ
F
130
0V
–100mV
Q
Q
Figure 2. Response Time Test Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| LT1671IS8 | 60ns, Low Power, Single Supply, Ground-Sensing Comparator |
| LT1675CMS8-1 | 250MHz, Triple and Single RGB Multiplexer with Current Feedback Amplifiers |
| LT1675CGN | 250MHz, Triple and Single RGB Multiplexer with Current Feedback Amplifiers |
| LT1675CS8-1 | 250MHz, Triple and Single RGB Multiplexer with Current Feedback Amplifiers |
| LT1676C | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1671CS8#PBF | 功能描述:IC COMP GRND-SENSNG LOWPWR 8SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 比较器 系列:- 标准包装:1 系列:- 类型:通用 元件数:1 输出类型:CMOS，开路集电极，TTL 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V 电压 - 输入偏移（最小值）:7mV @ 5V 电流 - 输入偏压（最小值）:0.25µA @ 5V 电流 - 输出（标准）:84mA @ 5V 电流 - 静态（最大值）:120µA CMRR, PSRR（标准）:- 传输延迟（最大）:600ns 磁滞:- 工作温度:-40°C ~ 85°C 封装/外壳:SC-74A，SOT-753 安装类型:表面贴装 包装:剪切带 (CT) 产品目录页面:1268 (CN2011-ZH PDF) 其它名称:*LMV331M5*LMV331M5/NOPBLMV331M5CT |
| LT1671CS8#PBF | 制造商:Linear Technology 功能描述:Micropower Comparator IC |
| LT1671CS8#TR | 功能描述:IC COMPARATOR 60NS LOW PWR 8SOIC RoHS:否 类别:集成电路 (IC) >> 线性 - 比较器 系列:- 标准包装:25 系列:- 类型:带电压基准 元件数:4 输出类型:CMOS，开路漏极，TTL 电压 - 电源，单路/双路(±):2 V ~ 11 V，±1 V ~ 5.5 V 电压 - 输入偏移（最小值）:10mV @ 5V 电流 - 输入偏压（最小值）:- 电流 - 输出（标准）:0.015mA @ 5V 电流 - 静态（最大值）:8.5µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:12µs 磁滞:50mV 工作温度:0°C ~ 70°C 封装/外壳:16-DIP（0.300"，7.62mm） 安装类型:通孔 包装:管件 |
| LT1671CS8#TRPBF | 功能描述:IC COMP GRND-SENSNG LOWPWR 8SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 比较器 系列:- 标准包装:25 系列:- 类型:带电压基准 元件数:4 输出类型:CMOS，开路漏极，TTL 电压 - 电源，单路/双路(±):2 V ~ 11 V，±1 V ~ 5.5 V 电压 - 输入偏移（最小值）:10mV @ 5V 电流 - 输入偏压（最小值）:- 电流 - 输出（标准）:0.015mA @ 5V 电流 - 静态（最大值）:8.5µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:12µs 磁滞:50mV 工作温度:0°C ~ 70°C 封装/外壳:16-DIP（0.300"，7.62mm） 安装类型:通孔 包装:管件 |
| LT1671CS8PBF | 制造商:Linear Technology 功能描述:Comparator 60ns Low Power 5V SOIC8 |
发布紧急采购，3分钟左右您将得到回复。