- 您现在的位置：买卖IC网 > PDF目录14028 > LT1676IS8#TR (Linear Technology)IC REG BUCK ADJ 0.7A 8SOIC PDF资料下载
参数资料
| 型号： | LT1676IS8#TR |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 0.7A 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.24 V ~ 51 V |
| 输入电压： | 7.4 V ~ 60 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 100kHz |
| 电流 - 输出： | 700mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-SOIC |
LT1676
APPLICATIO N S I N FOR M ATIO N
frequency resonance problems, proper layout of the com-
ponents connected to the IC is essential, especially the
power path. B field (magnetic) radiation is minimized by
keeping output diode, switch pin and intput bypass
capacitor leads as short as possible. E field radiation is
kept low by minimizing the length and area of all traces
connected to the switch pin (V SW ). A ground plane should
always be used under the switcher circuitry to prevent
interplane coupling.
The high speed switching current path is shown schemati-
cally in Figure 3. Minimum lead length in these paths is
essential to ensure clean switching and minimal EMI. The
paths containing the input capacitor, output switch and
output diode are the only ones containing nanosecond rise
and fall times. Keep these paths as short as possible.
Additionally, it is possible for the LT1676 to cause EMI
problems by “coupling to itself”. Specifically, this can
occur if the V SW pin is allowed to capacitively couple in an
uncontrolled manner to the part’s high impedance nodes,
i.e., SHDN, SYNC, V C and FB. This can cause erratic
operation such as odd/even cycle behavior, pulse width
“nervousness”, improper output voltage and/or prema-
ture current limit action.
As an example, assume that the capacitance between the
V SW node and a high impedance pin node is 0.1pF, and
further assume that the high impedance node in question
exhibits a capacitance of 1pF to ground. Due to the high
dV/dt, large excursion behavior of the V SW node, this will
couple a nearly 5V transient to the high impedance pin,
causing abnormal operation. (This assumes the “typical”
48V IN to 5V OUT application.) An explicit 100pF capacitor
added to the node will reduce the amplitude of the distur-
bance to more like 50mV (although settling time will
increase).
Specific pin recommendations are as follows:
SHDN: If unused, add a 100pF capacitor to ground.
SYNC: Ground if unused.
V C : Add a capacitor directly to ground in addition to the
V IN
+
C1
LT1676
V IN
V SW
D1
L1
+
C2
V OUT
explicit compensation network. A value of one-tenth of
the main compensation capacitor is recommended, up
to a maximum of 100pF.
FB: Assuming the V C pin is handled properly, this pin
usually requires no explicit capacitor of its own, but
1676 F03
Figure 3. High Speed Current Switching Paths
TYPICAL APPLICATIO N S
Minimum Component Count Application
Figure 4a shows a basic “minimum component count”
application. The circuit produces 5V at up to 500mA I OUT
with input voltages in the range of 12V to 48V. The typical
P OUT /P IN efficiency is shown in Figure 4b. No pulse
skipping is observed down to zero external load. As
shown, the SHDN and SYNC pins are unused, however
either (or both) can be optionally driven by external signals
as desired.
keep this node physically small to minimize stray ca-
pacitance.
User Programmable Undervoltage Lockout
Figure 5 adds a resistor divider to the basic application.
This is a simple, cost-effective way to add a user-program-
mable undervoltage lockout (UVLO) function. Resistor R5
is chosen to have approximately 200 μ A through it at the
nominal SHDN pin lockout threshold of roughly 1.25V.
The somewhat arbitrary value of 200 μ A was chosen to be
significantly above the SHDN pin input current to minimize
its error contribution, but significantly below the typical
3.2mA the LT1676 draws in lockout mode. Resistor R4 is
then chosen to yield this same 200 μ A, less 2.5 μ A, with the
11
相关PDF资料 |
PDF描述 |
|---|---|
| HM79S-125820LFTR13 | SHIELDED DRUM INDUCTORS |
| HM79S-125680LFTR13 | SHIELDED DRUM INDUCTORS |
| LT1303IS8-5#PBF | IC REG BOOST 5V 0.2A 8SOIC |
| HM79S-125560LFTR13 | SHIELDED DRUM INDUCTORS |
| LT1303IS8-5 | IC REG BOOST 5V 0.2A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1677 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Noise, Rail-to-Rail Precision Op Amp |
| LT1677_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Noise, Rail-to-Rail Precision Op Amp |
| LT1677C | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Noise, Rail-to-Rail Precision Op Amp |
| LT1677CN8 | 功能描述:IC OPAMP R-R I/O SGL LN 8DIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT1677CN8#PBF | 功能描述:IC OPAMP R-R I/O SGL LN 8DIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。