参数资料
| 型号： | LT1683EG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/26页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM CM 20-SSOP |
| 标准包装： | 66 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 250kHz |
| 占空比： | 46% |
| 电源电压： | 4 V ~ 20 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1328 (CN2011-ZH PDF) |
LT1683
APPLICATIONS INFORMATION
RA =
= 23.4k
RB =
= 1.75k
Soifwewantedtoturnonat20Vwith2Vofhysteresis:
2V ? 1.39V ? 20V ? 0.1V
24μA ? 1.39V
2V ? 1.39V ? 20V ? 0.1V
24μA ? (20V ? 1.39V)
Resistor values could be altered further by adding Zeners
in the divider string. A resistor in series with SHDN pin
could further change hysteresis without changing turn-on
voltage.
Frequency Compensation
Loop frequency compensation is accomplished by way of
a series RC network on the output of the error amplifier
(V C pin).
maximum output load current and will also be increased
if poor quality (high ESR) output capacitors are used. The
addition of a 0.0047μF capacitor for C VC2 pin reduces
switching frequency ripple to only a few millivolts. A low
value for R VC will also reduce V C pin ripple, but loop phase
margin may be inadequate.
Setting Current Limit
The sense resistor sets the value for maximum operating
current. When the CS pin voltage is 0.1V the gate drivers will
immediately go low (no slew control). Therefore the sense
resistor value should be set to R S = 0.1V/I SW(PEAK) , where
I SW(PEAK) is the peak current in the MOSFETs. I SW(PEAK)
will depend on the topology and component values and
tolerances. Certainly it should be set below the saturation
current value for the transformer.
R VC
2k
C VC
0.01 μ F
C VC2
4.7nF
Figure 6
V C PIN
1683 F06
If CS pin voltage is 0.22V in addition to the drivers going
low, V C and SS will be discharged to ground. This is to
provide additional protection in the event of a short cir-
cuit. By discharging V C and SS, the MOSFET will not be
stressed as hard on subsequent cycles since the current
trip will be set lower.
V CPINRIPPLE =
ReferringtoFigure6,themainpoleisformedbycapaci-
tor C VC and the output impedance of the error amplifier
(approximately 400kΩ). The series resistor, R VC , creates a
“zero” which improves loop stability and transient response.
A second capacitor, C VC2 , typically one-tenth the size of
the main compensation capacitor, is sometimes used to
reduce the switching frequency ripple on the V C pin. V C
pin ripple is caused by output voltage ripple attenuated
by the output divider and multiplied by the error amplifier.
Without the second capacitor, V C pin ripple is:
1.25 ? V RIPPLE ? gm ? R VC
V OUT
where V RIPPLE = Output ripple (V P-P )
gm = Error amplifier transconductance
R VC = Series resistor on V C pin
V OUT = DC output voltage
To prevent irregular switching, V C pin ripple should be
kept below 50mV P-P . Worst-case V C pin ripple occurs at
Turn-off of the MOSFETs will normally be inhibited for
about 100ns at the start of every turn on cycle. This is
to prevent noise from interfering with normal operation
of the controller. This current sense blanking does not
prevent the outputs from be turned off in the event of
a fault. Slewing of the gate voltage effectively provides
additional blanking.
Traces to the SENSE resistor should be kept short and
wide to minimize resistance and inductance. Large
interwinding capacitance in the transformer or high
capacitance on the drain of the MOSFETs will produce
a current pulse through the sense resistor during drain
voltage slewing. The magnitude of the pulse is C ? dV/dt
where C is the capacitance and dV/dt is the voltage slew
rate which is controlled by the part. This pulse will increase
the sensed current on switch turn-on and can cause pre-
mature MOSFET turn-off. If this occurs, the transformer
may need a different winding technique (see AN39) or
alternatively, a blanking circuit can be used. Please contact
the LTC applications group for support if required.
1683fd
16
相关PDF资料 |
PDF描述 |
|---|---|
| LT1725IGN#TR | IC REG CTRLR FLYBK ISO CM 16SSOP |
| LT1737IGN#PBF | IC REG CTRLR FLYBK ISO CM 16SSOP |
| LT1738EG#PBF | IC REG CTRLR PWM CM 20-SSOP |
| LT1761IS5-2.5#TRMPBF | IC REG LDO 2.5V .1A TSOT23-5 |
| LT1762EMS8-3.3#TR | IC REG LDO 3.3V .15A 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1683IG | 功能描述:IC REG CTRLR PWM CM 20-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT1683IG#PBF | 功能描述:IC REG CTRLR PWM CM 20-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT1683IG#TR | 功能描述:IC REG CTRLR PWM CM 20-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT1683IG#TRPBF | 功能描述:IC REG CTRLR PWM CM 20-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT1684 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Ring Tone Generator |
发布紧急采购，3分钟左右您将得到回复。