- 您现在的位置：买卖IC网 > PDF目录15275 > LT1738IG#PBF (Linear Technology)IC REG CTRLR PWM CM 20-SSOP PDF资料下载
参数资料
| 型号： | LT1738IG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/20页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM CM 20-SSOP |
| 标准包装： | 66 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 250kHz |
| 占空比： | 93.5% |
| 电源电压： | 2.55 V ~ 20 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 是 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
LT1738
APPLICATIO S I FOR ATIO
The worst component from an AC point is the gate charge
current. The actual peak current depends on gate capaci-
tance and slew rate, being higher for larger values of each.
The total current can be estimated by gate charge and
frequency of operation. Because of the slewing with this
low to reduce capacitor dissipation. Typically ESR should
be below 0.05 ? .
The capacitance value can be computed by consideration
of desired load ripple, duty cycle and ESR.
part gate charge is spread out over a longer time period
than with a normal FET driver. This reduces capacitance
requirements.
C OUT =
1
? V OUT
? I L ( MAX )
? ESR
?
DC MIN
f
Typically the current will have spikes of under 100mA
C IN =
? V CAP
? ESR
2 2 ?
? V IN ON ? ? I 2 +
? ? ?
I 2 +
? ?
4 +
P = ? V IN ?
? I ?
?
?
?
?
located at the gate voltage transitions. This is charge/
discharge to and from the threshold voltage. Most slewing
occurs with the gate voltage near threshold.
Since the part’s V IN will typically be under 15V many
options are available for choice of capacitor. Values of
input capacitor for just the V IN requirement will typically be
in the 50 μ F range with an ESR of under 0.1 ? .
In addition to the part’s supply, decoupling of the supply
to the inductor needs to be considered. If this is the same
supply as the V IN pin then that capacitor will need to be
increased. However, often with this part the inductor
supply will be a higher voltage and as such will use a
separate capacitor.
The inductor’s decoupling capacitor will see the switch
current as ripple.
The above switch current computation can be used to
estimate the capacity for these capacitors.
1 DC MIN
?
f
? I SW ( MAX )
where ? V CAP is the allowed sag on the input capacitor.
ESR is the equivalent series resistance for the cap. In
general allowed sag will be a few tenths of a volt.
Output Filter Capacitor
The output capacitor is chosen both for capacity and ESR.
The capacity must supply the load current in the switch on
state. While slew control reduces higher frequency com-
ponents of the ripple current in the capacitor, the capacitor
ESR and the magnitude of the output ripple current
controls the fundamental component. ESR should also be
MOSFET Selection
There is a wide variety of MOSFETs to choose from for this
part. The part will work with either normal threshold (3V to
4V) or logic level threshold devices (1V to 2V).
Select a voltage rating to insure under worst-case condi-
tions that the MOSFET will not break down. Next choose an
R ON sufficiently low to meet both the power dissipation
capabilities of the MOSFET package as well as overall
efficiency needs of the converter.
The LT1738 can handle a large range of gate charges.
However at very large charge stability may be affected.
The power dissipation in the MOSFET depends on several
factors. The primary element is I 2 R heating when the
device is on. In addition, power is dissipated when the
device is slewing. An estimate for power dissipation is:
? ? 3 ? ? I 2 ? ? ?
? ? I 2 ? R
?
? ? 4 ? ? ?
I SR V SR
? ?
? f + I 2 ? R ON ? DC
where I is the average current, ? I is the ripple current in the
switch, I SR is the current slew rate, V SR is the voltage slew
rate, f is the oscillator frequency, DC is the duty cycle and
R ON is the MOSFET on-resistance.
Setting GCL Voltage
Setting the voltage on the GCL pin depends on what type
of MOSFET is used and the desired gate drive undervolt-
age lockout voltage.
1738fa
17
相关PDF资料 |
PDF描述 |
|---|---|
| VE-25J-EY-F4 | CONVERTER MOD DC/DC 36V 50W |
| VI-2TP-EW-F2 | CONVERTER MOD DC/DC 13.8V 100W |
| EBC25DRXI-S734 | CONN EDGECARD 50POS DIP .100 SLD |
| LTC1709EG-7#TR | IC REG CTRLR BUCK PWM CM 36-SSOP |
| VI-2TN-EY-B1 | CONVERTER MOD DC/DC 18.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1739 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | BJT | NPN | 100V V(BR)CEO | 300MA I(C) | TO-39 |
| LT1739CFE | 功能描述:IC AMP XDSL LINE DRV DUAL20TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
| LT1739CFE#PBF | 功能描述:IC AMP LINE DVR DUAL 20-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
| LT1739CFE#TR | 功能描述:IC AMP XDSL LINE DRV DUAL20TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
| LT1739CFE#TRPBF | 功能描述:IC AMP XDSL LINE DRV DUAL20TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。