参数资料
| 型号： | LT1769CGN |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER CONST I/V 28SSOP |
| 标准包装： | 49 |
| 功能： | 充电管理 |
| 电池化学： | 铅酸，锂离子，镍镉，镍氢 |
| 电源电压： | 8 V ~ 25 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1340 (CN2011-ZH PDF) |
LT1769
APPLICATIO N S I N FOR M ATIO N
( ) ( )( )
R S2 2.465V R S2
V UV = Rising lockout threshold on the UV pin
V IN = Charger input voltage that will sustain full load power
Example: With R6 = 5k, V UV = 6.7V and setting V IN at 12V;
R5 = 5k (12V – 6.7V)/6.7V = 4k
The resistor divider should be connected directly to the
adapter output as shown, not to the V CC pin, to prevent
battery drain with no adapter voltage. If the UV pin is not
used, connect it to the adapter output (not V CC ) and
connect a resistor no greater than 5k to ground. Floating
this pin will cause reverse battery current to increase from
3 μ A to 200 μ A.
If connecting the unused UV pin to the adapter output is not
possible, it can be grounded. Although it would seem that
grounding the pin creates a permanent lockout state, the
UV circuitry is arranged for phase reversal with low volt-
ages on the UV pin to allow the grounding technique to work.
adapter load current remains below the limit. Amplifier
CL1 in Figure 2 senses the voltage across R S4 , connected
between the CLP and CLN pins. When this voltage exceeds
100mV, the amplifier will override the programmed charge
current to limit adapter current to 100mV/R S4 . A lowpass
filter formed by 500 ? and 1 μ F is required to eliminate
switching noise. If the input current limit is not used, both
CLP and CLN pins should be connected to V CC .
Charge Current Programming
The basic formula for charge current is (see Block
Diagram):
I BAT = I PROG =
R S1 R PROG R S1
where R PROG is the total resistance from PROG pin to ground.
For the sense amplifier CA1 biasing purpose, R S3 should
have the same value as R S2 and SPIN should be connected
+
CL1
–
LT1769
100mV
+
CLP
CLN
V CC
+
1 μ F
500 ?
R S4 *
AC ADAPTER
OUTPUT
V IN
R5
directly to the sense resistor (R S1 ) as shown in the Block
Diagram.
For example, 2A charge current is needed. For low power
dissipation on R S1 and enough signal to drive the amplifier
CA1, let R S1 = 100mV/2A = 0.05 ? . This limits R S1 power
to 0.2W. Let R PROG = 5k, then:
R S2 = R S3 = BAT
UV
*R S4 =
100mV
ADAPTER CURRENT LIMIT
R6
(I
)(R PROG )(R S1 )
2.465V
= = 200 ?
Figure 2. Adapter Input Current Limiting
1769 F02
(2A)(5k)(0.05)
2.465V
Adapter Current Limiting
An important feature of the LT1769 is the ability to
automatically adjust charge current to a level which avoids
overloading the wall adapter. This allows the product to
operate at the same time the batteries are being charged
without complex load management algorithms. Addition-
ally, batteries will automatically be charged at the maximum
possible rate of which the adapter is capable.
This is accomplished by sensing total adapter output
current and adjusting the charge current downward if a
preset adapter current limit is exceeded. True analog
control is used, with closed-loop feedback ensuring that
Charge current can also be programmed by pulse width
modulating I PROG with a switch Q1 to R PROG at a frequency
higher than a few kHz (Figure 3). Charge current will be
proportional to the duty cycle of the switch with full current
at 100% duty cycle.
Lithium-Ion Charging
The 2A Lithium-Ion Battery Charger (Figure 1) charges at
a constant 2A until battery voltage reaches a limit set by R3
and R4. The charger will then automatically go into a
constant-voltage mode with current decreasing to near
zero over time as the battery reaches full charge. This is the
normal regimen for lithium-ion charging, with the charger
1769fa
10
相关PDF资料 |
PDF描述 |
|---|---|
| LT1776IS8#TR | IC REG BUCK ADJ 0.7A 8SOIC |
| LT1777IS#TRPBF | IC REG BUCK ADJ 0.7A 16SOIC |
| LT1786FCS#TR | IC REG SW CCFL SMBUS PROG 16SOIC |
| LT1912EMSE#TRPBF | IC REG BUCK ADJ 2A 10MSOP |
| LT1913IDD#TRPBF | IC REG BUCK ADJ 3.5A 10DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1769CGN#PBF | 功能描述:IC BATT CHARGER CONST I/V 28SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LT1769CGN#TR | 功能描述:IC CHARGER BATT CONST V/I 28SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT1769CGN#TRPBF | 功能描述:IC BATT CHARGER CONST I/V 28SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT1769IFE | 功能描述:IC BATT CHRGR CNSTNT I/V 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT1769IFE#PBF | 功能描述:IC BATT CHRGR CNSTNT I/V 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。