参数资料
| 型号： | LT1786FCS#TR |
| 厂商： | Linear Technology |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC REG SW CCFL SMBUS PROG 16SOIC |
| 标准包装： | 2,500 |
| 应用： | 转换器，CCFL |
| 输入电压： | 4.5 V ~ 30 V |
| 输出数： | 1 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
LT1786F
PI N FU N CTIO N S
AGND (Pin 5): This is the low current analog ground. It is
the negative sense terminal for the internal 1.24V refer-
ence and the I CCFL summing voltage in the LT1786F.
Connect low current signal paths that terminate to ground
and frequency compensation components that terminate
to ground directly to this pin for best regulation and
performance.
SHDN (Pin 6): Pulling this pin low causes regulator
shutdown with quiescent current typically reduced to
150 μ A. In this condition, the DAC circuitry remains alive
and the DAC I OUT level is maintained. If this pin is not used,
use a pull-up resistor to force a logic high level (maximum
of 6V). The pin can be floated and an internal current
source will pull the pin to a logic high level. However, poor
PCB layout techniques can permit switching noise to inject
into this pin and cause erratic operation. LTC recommends
the use of a pull-up resistor. If the SMBSUS pin is pulled
low or Bit 7 = 1 in the Command Byte, complete IC
shutdown is enabled. An internal open drain N-channel
device turns on and pulls the SHDN pin low. The N-channel
can sink up to 1.6mA.
SMBSUS (Pin 7): Pulling this pin low causes complete
shutdown for the IC with quiescent current typically
reduced to 40 μ A. In this SMBus suspend condition, the
DAC retains its last output current setting and returns to
this level when the logic low signal at this pin is removed.
If this pin is not used, use a pull-up resistor to force a
logic high level or tie it directly to V CC . Poor PCB layout
techniques can permit switching noise to inject into this
pin and cause erratic operation. A small value capacitor
may be required to filter out this noise. Setting Bit 7 = 1
in the Command Byte also enables an SMBus suspend
condition. Enabling an SMBus suspend condition turns
on an internal open drain N-channel device which pulls
the SHDN pin low. The N-channel device sinks up to
1.6mA at the SHDN pin.
ADR (Pin 8): This is the SMBus address select pin. Tie this
pin to either V CC or GND to select one of two SMBus
addresses to which the LT1786F will respond. If the ADR
8
pin is tied to GND, the SMBus address is set to 5A (HEX)
and the DAC I OUT powers up to zero scale. If the ADR pin
is tied to V CC , the SMBus address is set to 58 (HEX) and
the DAC I OUT powers up to half scale. If a different value is
required for the DAC I OUT on power-up, use the SHDN pin
to keep the CCFL regulator off until the required value has
been programmed for the DAC via the SMBus.
SDA (Pin 9): This is the SMBus bidirectional data input and
digital output pin. Data is shifted into the SDA pin and
acknowledged by the SDA pin. SDA is a high impedance
pin while data is shifted into the pin and an open-drain
N-channel output during acknowledges. SDA requires a
pull-up resistor or current source to V CC .
SCL (Pin 10): This is the SMBus clock input pin. Data is
shifted into the SDA pin at the rising edges of the SCL clock
during data transfer. SCL is a high impedance pin. SCL
requires a pull-up resistor or current source to V CC .
I OUT (Pin 11): This pin is the current output for the DAC and
provides a full-scale output current of 100 μ A ± 4 μ A over
temperature. Initial accuracy is 100 μ A ± 2 μ A.The pin can
be biased from – 10V to (V CC – 1.3V). This pin is typically
tied directly to the I CCFL pin and provides the programming
current which sets the operating lamp current. The I OUT
pin has very little bias voltage change when tied to the I CCFL
pin as I CCFL is regulated. The programming current is
sourced from the I OUT pin and sunk by the I CCFL pin.
V CC (Pin 12): This is the supply pin for the LT1786F. The
IC accepts an input voltage range of 3V minimum to 6.5V
maximum with little change in quiescent current (zero
switch current). An internal, low-dropout regulator pro-
vides a 2.4V supply for most of the internal circuitry.
Supply current increases as switch current increases at a
rate approximately 1/50 of switch current. This corre-
sponds to a forced Beta of 50 for the power switch. The IC
incorporates undervoltage lockout by sensing regulator
dropout and locking out switching for input voltages
below 2.5V. Hysteresis is not used to maximize the range
of input voltage. The typical input voltage is a 3.3V or 5V
logic supply.
相关PDF资料 |
PDF描述 |
|---|---|
| LT1912EMSE#TRPBF | IC REG BUCK ADJ 2A 10MSOP |
| LT1913IDD#TRPBF | IC REG BUCK ADJ 3.5A 10DFN |
| LT1930AES5#TRM | IC REG BOOST ADJ 1A TSOT23-5 |
| LT1931AIS5#TRPBF | IC REG INV 1A TSOT23-5 |
| LT1933HS6#TRMPBF | IC REG BUCK ADJ 0.6A TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1787 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Precision, High Side Current Sense Amplifiers |
| LT1787_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Precision, High Side Current Sense Amplifiers |
| LT1787CMS8 | 功能描述:IC AMP PREC CURRENT SENSE 8MSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
| LT1787CMS8#PBF | 功能描述:IC AMP PREC CURRENT SENSE 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
| LT1787CMS8#TR | 功能描述:IC AMP PREC CURRENT SENSE 8MSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
发布紧急采购，3分钟左右您将得到回复。