- 您现在的位置：买卖IC网 > PDF目录14824 > LT1912EDD#PBF (Linear Technology)IC REG BUCK ADJ 2A 10DFN PDF资料下载
参数资料
| 型号： | LT1912EDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 2A 10DFN |
| 标准包装： | 121 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.79 V ~ 20 V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 500kHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-DFN（3x3） |
| 产品目录页面： | 1329 (CN2011-ZH PDF) |
LT1912
APPLICATIONS INFORMATION
C OUT =
withalowerDCRresultinginhigherefficiency.Thereare
several graphs in the Typical Performance Characteristics
section of this data sheet that show the maximum load
current as a function of input voltage and inductor value
for several popular output voltages. Low inductance may
result in discontinuous mode operation, which is okay
but further reduces maximum load current. For details of
maximum output current and discontinuous mode opera-
tion, see Linear Technology Application Note 44. Finally,
for duty cycles greater than 50% (V OUT /V IN > 0.5), there
is a minimum inductance required to avoid subharmonic
oscillations. See AN19.
Input Capacitor
Bypass the input of the LT1912 circuit with a ceramic capaci-
tor of X7R or X5R type. Y5V types have poor performance
over temperature and applied voltage, and should not be
used. A 4.7μF to 10μF ceramic capacitor is adequate to
bypass the LT1912 and will easily handle the ripple current.
Note that larger input capacitance is required when a lower
switching frequency is used. If the input power source has
high impedance, or there is significant inductance due to
long wires or cables, additional bulk capacitance may be
necessary. This can be provided with a lower performance
electrolytic capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT1912 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 4.7μF capacitor is capable of this task, but only if it is
placed close to the LT1912 and the catch diode (see the
PCB Layout section). A second precaution regarding the
ceramic input capacitor concerns the maximum input
voltage rating of the LT1912. A ceramic input capacitor
combined with trace or cable inductance forms a high
quality (under damped) tank circuit. If the LT1912 circuit
is plugged into a live supply, the input voltage can ring to
twice its nominal value, possibly exceeding the LT1912’s
voltage rating. This situation is easily avoided (see the Hot
Plugging Safely section).
Output Capacitor and Output Ripple
The output capacitor has two essential functions. Along
with the inductor, it filters the square wave generated by the
LT1912 to produce the DC output. In this role it determines
the output ripple, and low impedance at the switching
frequency is important. The second function is to store
energy in order to satisfy transient loads and stabilize the
LT1912’s control loop. Ceramic capacitors have very low
equivalent series resistance (ESR) and provide the best
ripple performance. A good starting value is:
100
V OUT f SW
where f SW is in MHz, and C OUT is the recommended output
capacitance in μF. Use X5R or X7R types. This choice will
provide low output ripple and good transient response.
Transient performance can be improved with a higher value
capacitor if the compensation network is also adjusted
to maintain the loop bandwidth. A lower value of output
capacitor can be used to save space and cost but transient
performance will suffer. See the Frequency Compensation
section to choose an appropriate compensation network.
When choosing a capacitor, look carefully through the
data sheet to find out what the actual capacitance is under
operating conditions (applied voltage and temperature).
A physically larger capacitor, or one with a higher voltage
rating, may be required. High performance tantalum or
electrolytic capacitors can be used for the output capacitor.
Low ESR is important, so choose one that is intended for
use in switching regulators. The ESR should be specified by
the supplier, and should be 0.05Ω or less. Such a capaci-
tor will be larger than a ceramic capacitor and will have a
larger capacitance, because the capacitor must be large to
achieve low ESR. Table 2 lists several capacitor vendors.
1912fa
11
相关PDF资料 |
PDF描述 |
|---|---|
| LT1172CT#PBF | IC REG MULTI CONFIG ADJ TO220 |
| 1120-390K | CHOKE RF RADIAL 39UH 10% |
| LT1425CS#PBF | IC REG FLYBK ISOLATED .2A 16SOIC |
| 1120-330K | CHOKE RF RADIAL 33UH 10% |
| LT1072CT#PBF | IC REG MULTI CONFIG ADJ TO220 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1912EDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 2A, 500kHz Step-Down Switching Regulator |
| LT1912EMSE#PBF | 功能描述:IC REG BUCK ADJ 2A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1912EMSE#TRPBF | 功能描述:IC REG BUCK ADJ 2A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1912EMSEPBF | 制造商:Linear Technology 功能描述:2A, 500kHz Step-Down Regulator LT1912EM |
| LT1912EMSE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 2A, 500kHz Step-Down Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。