参数资料
| 型号： | LT1936HMS8E#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.4A 8MSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.2 V ~ 31.3 V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 1.4A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-MSOP-EP |
LT1936
APPLICATIONS INFORMATION
inductance may result in discontinuous mode operation,
which is okay but further reduces maximum load current.
For details of maximum output current and discontinuous
mode operation, see Linear Technology Application Note
44. Finally, for duty cycles greater than 50% (V OUT /V IN
> 0.5), there is a minimum inductance required to avoid
subharmonic oscillations. Choosing L greater than 1.6
(V OUT + V D ) μH prevents subharmonic oscillations at all
duty cycles.
Catch Diode
A 1A Schottky diode is recommended for the catch diode,
D1. The diode must have a reverse voltage rating equal
to or greater than the maximum input voltage. The ON
Semiconductor MBRM140 is a good choice. It is rated
for 1A DC at a case temperature of 110°C and 1.5A at a
case temperature of 95°C. Diode Incorporated’s DFLS140L
is rated for 1.1A average current; the DFLS240L is rated
for 2A average current. The average diode current in an
LT1936 application is approximately I OUT (1 – DC).
Input Capacitor
Bypass the input of the LT1936 circuit with a 4.7μF or
higher value ceramic capacitor of X7R or X5R type. Y5V
types have poor performance over temperature and ap-
plied voltage, and should not be used. A 4.7μF ceramic
combined with trace or cable inductance forms a high
quality (under damped) tank circuit. If the LT1936 circuit
is plugged into a live supply, the input voltage can ring to
twice its nominal value, possibly exceeding the LT1936’s
voltage rating. This situation is easily avoided; see the Hot
Plugging Safety section.
For space sensitive applications, a 2.2μF ceramic capaci-
tor can be used for local bypassing of the LT1936 input.
However, the lower input capacitance will result in in-
creased input current ripple and input voltage ripple, and
may couple noise into other circuitry. Also, the increased
voltage ripple will raise the minimum operating voltage
of the LT1936 to ~3.7V.
Output Capacitor
The output capacitor has two essential functions. Along
with the inductor, it ?lters the square wave generated
by the LT1936 to produce the DC output. In this role it
determines the output ripple, and low impedance at the
switching frequency is important. The second function
is to store energy in order to satisfy transient loads and
stabilize the LT1936’s control loop.
Ceramic capacitors have very low equivalent series re-
sistance (ESR) and provide the best ripple performance.
A good value is:
is adequate to bypass the LT1936 and will easily handle
the ripple current. However, if the input power source has
high impedance, or there is signi?cant inductance due to
C OUT =
150
V OUT
long wires or cables, additional bulk capacitance may be
necessary. This can be provided with a low performance
electrolytic capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT1936 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 4.7μF capacitor is capable of this task, but only if it is
placed close to the LT1936 and the catch diode; see the
where C OUT is in μF. Use X5R or X7R types. This choice
will provide low output ripple and good transient response.
Transient performance can be improved with a high value
capacitor if the compensation network is also adjusted to
maintain the loop bandwidth.
A lower value of output capacitor can be used, but transient
performance will suffer. With an external compensation
network, the loop gain can be lowered to compensate for the
lower capacitor value. When using the internal compensa-
tion network, the lowest value for stable operation is:
PCB Layout section. A second precaution regarding the
ceramic input capacitor concerns the maximum input
voltage rating of the LT1936. A ceramic input capacitor
C OUT >
66
V OUT
1936fd
9
相关PDF资料 |
PDF描述 |
|---|---|
| LT1938IDD#TRPBF | IC REG BUCK ADJ 2.2A 10DFN |
| LT1940EFE#TRPBF | IC REG BUCK ADJ 1.4A DL 16TSSOP |
| LT1941EFE#TRPBF | IC REG MULTI CONFIG TRPL 28TSSOP |
| LT1942EUF#TRPBF | IC REG SW QUAD TFT LCD 24-QFN |
| LT1943EFE#TRPBF | IC REG SW QUAD TFT LCD 28-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1936IMS8E | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 3.6V to 36V 8-Pin MSOP EP |
| LT1936IMS8E#PBF | 功能描述:IC REG BUCK ADJ 1.4A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1936IMS8E#TRPBF | 功能描述:IC REG BUCK ADJ 1.4A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1936IMS8EPBF | 制造商:Linear Technology 功能描述:Switching Regulator 1.4A 500kHz MSOP8EP |
| LT1936IMS8E-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.4A, 500kHz Step-Down Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。