- 您现在的位置：买卖IC网 > PDF目录1823 > LT1952IGN-1#PBF (Linear Technology)IC REG CTRLR ISO PWM CM 16-SSOP PDF资料下载
参数资料
| 型号： | LT1952IGN-1#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR ISO PWM CM 16-SSOP |
| 标准包装： | 100 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 560kHz |
| 占空比： | 90% |
| 电源电压： | 6.82 V ~ 25 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1952/LT1952-1
OPERATION
Introduction
The LT1952/LT1952-1 are current mode synchronous
PWM controllers optimized for control of the simplest
forward converter topology—using only one primary
MOSFET. The LT1952/LT1952-1 are ideal for 25W to 500W
power systems where very high efficiency and reliability,
low complexity and cost are required in a small space.
Key features of the LT1952/LT1952-1 include an adaptive
maximum duty cycle clamp for the single primary MOSFET.
An additional output signal is included for synchronous
rectifier control. A precision 107mV threshold senses
overcurrent conditions and triggers Soft-Start for low
stress short-circuit protection and control. The key
functions of the LT1952/LT1952-1 are shown in the Block
Diagram in Figure 2.
Part Start-up
In normal operation the SD_V SEC pin must exceed 1.32V
and the V IN pin must exceed 14.25V (7.75V LT1952-1) to
allow the part to turn on. This combination of pin voltages
allows the 2.5V V REF pin to become active, supplying the
LT1952/LT1952-1 control circuitry and providing up to
2.5mA external drive. SD_V SEC threshold can be used for
externally programming an undervoltage lockout (UVLO)
threshold on the system input voltage. Hysteresis on
the UVLO threshold can also be programmed since the
SD_V SEC pin draws 11μA just before part turn on and 0μA
after part turn on.
With the LT1952/LT1952-1 turned on, the V IN pin can drop
as low as 8.75V (6.5V LT1952-1) before part shutdown
occurs. This V IN pin hysteresis (5.5V LT1952; 1.25V
LT1952-1) combined with low 460μA (400μA LT1952-1)
start-up input current allows low power start-up using
a resistor/capacitor network from system V IN to supply
the V IN pin (Figure 3). The V IN capacitor value is chosen
to prevent V IN falling below its turn off threshold before
an auxiliary winding in the converter takes over supply
to the V IN pin.
Output Drivers
The LT1952/LT1952-1 have two outputs, SOUT and OUT.
The OUT pin provides a ± 1A peak MOSFET gate drive
clamped to 13V. The SOUT pin has a ± 50mA peak drive
clamped to 12V and provides sync signal timing for syn-
chronous rectification control.
For SOUT and OUT turn on, a PWM latch is set at the start
of each main oscillator cycle. OUT turn on is delayed from
SOUT turn on by a time t DELAY (Figure 2). t DELAY is pro-
grammed using a resistor from the DELAY pin to ground
and is used to set the timing control of the secondary
synchronous rectifiers for optimum efficiency.
SOUT and OUT turn off at the same time each cycle by
one of three methods:
(1) MOSFET peak current sense at I SENSE pin
(2) Adaptive maximum duty cycle clamp reached during
load/line transients
(3) Maximum duty cycle reset of the PWM latch
During any of the following conditions —low V IN , low
SD_V SEC or overcurrent detection at the OC pin —a soft-
start event is latched and both SOUT and OUT turn off
immediately (Figure 1).
Leading Edge Blanking
To prevent MOSFET switching noise causing premature turn
off of SOUT or OUT, programmable leading edge blanking
exists. This means both the current sense comparator
and overcurrent comparator outputs are ignored during
MOSFET turn on and for an extended period after the OUT
leading edge (Figure 6). The extended blanking period is
programmable by adjusting a resistor from the BLANK
pin to ground.
Adaptive Maximum Duty Cycle Clamp
(Volt-Second Clamp)
For forward converter applications using the simplest
topology of a single MOSFET on the primary, a maximum
switch duty cycle clamp which adapts to transformer input
voltage is necessary for reliable control of the MOSFET. This
volt-second clamp provides a safeguard for transformer
reset that prevents transformer saturation. Instantaneous
load changes can cause the converter loop to demand
maximum duty cycle. If the maximum duty cycle of the
switch is too great, the transformer reset voltage can
exceed the voltage rating of the primary-side MOSFET with
19521fe
11
相关PDF资料 |
PDF描述 |
|---|---|
| LT1956IFE-5#TRPBF | IC REG BUCK 5V 1.5A 16TSSOP |
| LT1959IR#TR | IC REG BUCK ADJ 4.5A D2PAK |
| LT1961IMS8E#TRPBF | IC REG BOOST ADJ 1.5A 8MSOP |
| LT1962EMS8-1.8#TRPBF | IC REG LDO 1.8V .3A 8MSOP |
| LT1963AMPQ#TRPBF | IC REG LDO ADJ 1.5A 5-DD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1952IGN-1TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single Switch Synchronous Forward Controller |
| LT1952IGN-1TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single Switch Synchronous Forward Controller |
| LT1952IGNPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single Switch Synchronous Forward Controller |
| LT1952IGNTR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single Switch Synchronous Forward Controller |
| LT1952IGNTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single Switch Synchronous Forward Controller |
发布紧急采购，3分钟左右您将得到回复。