- 您现在的位置：买卖IC网 > PDF目录13925 > LT1956IGN-5 (Linear Technology)IC REG BUCK 5V 1.5A 16SSOP PDF资料下载
参数资料
| 型号： | LT1956IGN-5 |
| 厂商： | Linear Technology |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 5V 1.5A 16SSOP |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 5.5 V ~ 60 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 16-SSOP |
| 其它名称： | LT1956IGN5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1956/LT1956-5
APPLICATIO S I FOR ATIO
Board layout also has a significant effect on thermal resis-
tance. For the GN package, Pins 1, 8, 9 and 16, GND, are
a continuous copper plate that runs under the LT1956 die.
This is the best thermal path for heat out of the package.
Reducing the thermal resistance from Pins 1, 8, 9 and 16
onto the board will reduce die temperature and increase
the power capability of the LT1956. This is achieved by
providing as much copper area as possible around these
pins. Adding multiple solder filled feedthroughs under and
around these four corner pins to the ground plane will also
help. Similar treatment to the catch diode and coil termi-
nations will reduce any additional heating effects. For the
FE package, the exposed pad should be soldered to the
copper ground plane underneath the device.
PARASITIC RESONANCE
Resonance or “ringing” may sometimes be seen on the
switch node (see Figure 7). Very high frequency ringing
following switch rise time is caused by switch/diode/input
capacitor lead inductance and diode capacitance. Schot-
tky diodes have very high “Q” junction capacitance that
can ring for many cycles when excited at high frequency.
If total lead length for the input capacitor, diode and switch
path is 1 inch, the inductance will be approximately 25nH.
At switch off, this will produce a spike across the NPN
output device in addition to the input voltage. At higher
currents this spike can be in the order of 10V to 20V or
higher with a poor layout, potentially exceeding the abso-
a >100MHz oscilloscope must be used, and waveforms
should be observed on the leads of the package. This
switch off spike will also cause the SW node to go below
ground. The LT1956 has special circuitry inside which
mitigates this problem, but negative voltages over 0.8V
lasting longer than 10ns should be avoided. Note that
100MHz oscilloscopes are barely fast enough to see the
details of the falling edge overshoot in Figure 7.
A second, much lower frequency ringing is seen during
switch off time if load current is low enough to allow the
inductor current to fall to zero during part of the switch off
time (see Figure 8). Switch and diode capacitance resonate
with the inductor to form damped ringing at 1MHz to 10
MHz. This ringing is not harmful to the regulator and it has
not been shown to contribute significantly to EMI. Any
attempt to damp it with a resistive snubber will degrade
efficiency.
THERMAL CALCULATIONS
Power dissipation in the LT1956 chip comes from four
sources: switch DC loss, switch AC loss, boost circuit
current, and input quiescent current. The following formu-
las show how to calculate each of these losses. These
formulas assume continuous mode operation, so they
should not be used for calculating efficiency at light load
currents.
Switch loss:
R SW ( I OUT ) ( V OUT )
lute max switch voltage. The path around switch, catch
diode and input capacitor must be kept as short as
possible to ensure reliable operation. When looking at this,
P SW =
2
V IN
+ t EFF ( 1 / 2 ) ( I OUT )( V IN )( f )
SW RISE
SW FALL
10V/DIV
SWITCH NODE
VOLTAGE
2V/DIV
0.2A/DIV
INDUCTOR
CURRENT AT
I OUT = 0.1A
V IN = 25V
500ns/DIV
1956 F08
50ns/DIV
1956 F07
V OUT = 5V
L = 15 μ H
Figure 7. Switch Node Resonance
Figure 8. Discontinuous Mode Ringing
1956f
18
相关PDF资料 |
PDF描述 |
|---|---|
| GEM40DCAH | CONN EDGECARD 80POS R/A .156 SLD |
| LT1766IGN-5 | IC REG BUCK 5V 1.5A 16SSOP |
| HM72A-12100LFTR13 | INDUCTOR 10UH HI PWR/PERF SMD |
| V150B28C150BF2 | CONVERTER MOD DC/DC 28V 150W |
| LT1766IGN | IC REG BUCK ADJ 1.5A 16SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1956IGN-5#PBF | 功能描述:IC REG BUCK 5V 1.5A 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1956IGN-5#TR | 功能描述:IC REG BUCK 5V 1.5A 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1956IGN-5#TRPBF | 功能描述:IC REG BUCK 5V 1.5A 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1956IGNPBF | 制造商:Linear Technology 功能描述:DC-DC Converter Step-Down 5.5-60V SSOP16 |
| LT1959 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A, 500kHz Step-Down Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。