- 您现在的位置：买卖IC网 > PDF目录1823 > LT1962EMS8-1.8#TRPBF (Linear Technology)IC REG LDO 1.8V .3A 8MSOP PDF资料下载
参数资料
| 型号： | LT1962EMS8-1.8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V .3A 8MSOP |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 最高 20V |
| 电压 - 压降（标准）： | 0.27V @ 300mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 300mA |
| 电流 - 限制（最小）： | 320mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
| 配用： | DC1075A-ND - BOARD COMPANION |
LT1962 Series
APPLICATIO S I FOR ATIO
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holes can also be used to spread the heat gener-
ated by power devices.
The following table lists thermal resistance for several
different board sizes and copper areas. All measurements
were taken in still air on 1/16" FR-4 board with one ounce
copper.
Table 1. Measured Thermal Resistance
T JMAX = 50 ° C + 35.3 ° C = 85.3 ° C
Protection Features
The LT1962 regulators incorporate several protection
features which make them ideal for use in battery-powered
circuits. In addition to the normal protection features
associated with monolithic regulators, such as current
limiting and thermal limiting, the devices are protected
against reverse input voltages, reverse output voltages
and reverse voltages from output to input.
Current limit protection and thermal overload protection
COPPER AREA
THERMAL RESISTANCE
are intended to protect the device against current overload
2500mm
2500mm
2500mm
1000mm
2500mm
2500mm
225mm
2500mm
2500mm
TOPSIDE*
2
2
2
100mm 2
BACKSIDE
2
2
2
2500mm 2
BOARD AREA
2
2
2
2500mm 2
(JUNCTION-TO-AMBIENT)
110 ° C/W
115 ° C/W
120 ° C/W
130 ° C/W
conditions at the output of the device. For normal opera-
tion, the junction temperature should not exceed 125 ° C.
The input of the device will withstand reverse voltages of
20V. Current flow into the device will be limited to less than
1mA (typically less than 100 μ A) and no negative voltage
2500mm
2500mm
50mm
2
2
2
140 ° C/W
will appear at the output. The device will protect both itself
*Device is mounted on topside.
Calculating Junction Temperature
Example: Given an output voltage of 3.3V, an input voltage
range of 4V to 6V, an output current range of 0mA to
100mA and a maximum ambient temperature of 50 ° C,
what will the maximum junction temperature be?
The power dissipated by the device will be equal to:
I OUT(MAX) (V IN(MAX) – V OUT ) + I GND (V IN(MAX) )
where,
I OUT(MAX) = 100mA
V IN(MAX) = 6V
I GND at (I OUT = 100mA, V IN = 6V) = 2mA
So,
P = 100mA(6V – 3.3V) + 2mA(6V) = 0.28W
The thermal resistance will be in the range of 110 ° C/W to
140 ° C/W depending on the copper area. So the junction
temperature rise above ambient will be approximately
equal to:
0.28W(125 ° C/W) = 35.3 ° C
The maximum junction temperature will then be equal to
the maximum junction temperature rise above ambient
plus the maximum ambient temperature or:
14
and the load. This provides protection against batteries
which can be plugged in backward.
The output of the LT1962 can be pulled below ground
without damaging the device. If the input is left open circuit
or grounded, the output can be pulled below ground by
20V. For fixed voltage versions, the output will act like a
large resistor, typically 500k or higher, limiting current
flow to less than 40 μ A. For adjustable versions, the output
will act like an open circuit; no current will flow out of the
pin. If the input is powered by a voltage source, the output
will source the short-circuit current of the device and will
protect itself by thermal limiting. In this case, grounding
the SHDN pin will turn off the device and stop the output
from sourcing the short-circuit current.
The ADJ pin of the adjustable device can be pulled above
or below ground by as much as 7V without damaging the
device. If the input is left open circuit or grounded, the ADJ
pin will act like an open circuit when pulled below ground
and like a large resistor (typically 100k) in series with a
diode when pulled above ground.
In situations where the ADJ pin is connected to a resistor
divider that would pull the ADJ pin above its 7V clamp
voltage if the output is pulled high, the ADJ pin input
current must be limited to less than 5mA. For example, a
resistor divider is used to provide a regulated 1.5V output
相关PDF资料 |
PDF描述 |
|---|---|
| LT1963AMPQ#TRPBF | IC REG LDO ADJ 1.5A 5-DD |
| LT1964IDD#TRPBF | IC REG LDO NEG ADJ .2A 8DFN |
| LT1965EQ-1.8#PBF | IC REG LDO 1.8V 1.1A 5-DDPAK |
| LT1976HFE#TRPBF | IC REG BUCK ADJ 1.5A 16TSSOP |
| LT1977IFE#TRPBF | IC REG BUCK ADJ 1.5A 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1962EMS8-2.5 | 功能描述:IC REG LDO 2.5V .3A 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| LT1962EMS8-2.5#PBF | 功能描述:IC REG LDO 2.5V .3A 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:MIC5365/66 Ultra-small LDO Regulators 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.155V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:200mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UDFN 裸露焊盘，4-TMLF? 供应商设备封装:4-TMLF?（1x1） 包装:Digi-Reel® 其它名称:576-3192-6 |
| LT1962EMS8-2.5#PBF | 制造商:Linear Technology 功能描述:IC VOLT REG FIXED +2.5V BIPOLAR TS |
| LT1962EMS8-2.5#TR | 功能描述:IC REG LDO 2.5V .3A 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| LT1962EMS8-2.5#TRPBF | 功能描述:IC REG LDO 2.5V .3A 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。