- 您现在的位置：买卖IC网 > PDF目录14802 > LT1976EFE#PBF (Linear Technology)IC REG BUCK ADJ 1.5A 16TSSOP PDF资料下载
参数资料
| 型号： | LT1976EFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.5A 16TSSOP |
| 标准包装： | 95 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.2 V ~ 54 V |
| 输入电压： | 3.3 V ~ 60 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 200kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-TSSOP-EP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1976/LT1976B
BLOCK DIAGRA
power from the V IN pin, but if the BIAS pin is connected to
an external voltage higher than 3V bias power will be
drawn from the external source (typically the regulated
output voltage). This improves efficiency.
High switch efficiency is attained by using the BOOST pin
to provide a voltage to the switch driver which is higher
than the input voltage, allowing switch to be saturated.
This boosted voltage is generated with an external capaci-
tor and diode.
To further optimize efficiency, the LT1976 automatically
switches to Burst Mode operation in light load situations.
APPLICATIO S I FOR ATIO
CHOOSING THE LT1976 OR LT1977
The LT1976/LT1976B and LT1977 are high voltage 1.5A
step-down switching regulators. The LT1976 and LT1977
contain circuitry which shifts into burst mode at light loads
reducing quiescent current to typically 100 μ A. The LT1976B
pulse skips in light load situations, eliminating low fre-
quency burst mode output ripple at the expense of light
load efficiency. The difference between the LT1976/
LT1976B and LT1977 is that the fixed switching frequency
of the LT1976/LT1976B is 200kHz versus 500kHz for the
LT1977. The switching frequency affects: inductor size,
input voltage range in continuous mode operation, effi-
ciency, thermal loss and EMI.
In Burst Mode operation, all circuitry associated with
controlling the output switch is shut down reducing the
input supply current to 45 μ A.
The only difference between the LT1976 and the LT1976B
is that the LT1976B does not shift into burst mode in light
load situations, eliminating low frequency output ripple at
the expense of light load efficiency.
The LT1976 contains a power good flag with a program-
mable threshold and delay time. A logic-level low on the
SHDN pin disables the IC and reduces input suppy current
to less than 1 μ A.
INPUT VOLTAGE RANGE
The minimum on and off times for all versions of the ic are
equivalent. This results in a narrower range of continuous
mode operation for the LT1977. Typical minimum and
maximum duty cycles are 6% to 92% for the LT1976/
LT1976B and 15% to 90% for the LT1977. Both parts will
regulate up to an input voltage of 60V but the LT1977 will
transistion into pulse-skipping/Burst Mode operation when
the input voltage is above 30V for a 5V output. At outputs
above 10V the LT1977’s input range will be similar to the
LT1976/LT1976B. Lowering the input voltage below the
maximum duty cycle limitation will cause a dropout in
regulation.
Table 1. LT1976/LT1976B/LT1977 Comparison
OUTPUT RIPPLE AND INDUCTOR SIZE
Output ripple current is determined by the input to output
voltage ratio, inductor value and switch frequency. Since
the switch frequency of the LT1977 is 2.5 times greater
than that of the LT1976/LT1976B, the inductance used in
the LT1977 application can be 2.5 times lower than the
LT1976/LT1976B while maintaining the same output ripple
current. The lower value used in the LT1977 application
allows the use of a physically smaller inductor.
PARAMETER
Minimum Duty Cycle
Maximum Duty Cycle
Inductor Size
Output Capacitor Size
Efficiency
EMI
Input Range
Output Ripple
Light Load Output Ripple
ADVANTAGE
LT1976/LT1976B
LT1976/LT1976B
LT1977
LT1977
LT1976
LT1976B
LT1976/LT1976B
LT1977
LT1976B
1976bfg
11
相关PDF资料 |
PDF描述 |
|---|---|
| RBM12DRMN-S664 | CONN EDGECARD 24POS .156 WW |
| LTC3442EDE#PBF | IC REG BUCK BOOST SYNC ADJ 12DFN |
| LT8582EDKD#PBF | IC REG MULTI CONFIG ADJ 3A 24DFN |
| MAX6423XS28+T | IC MPU/RESET CIRC 2.80V SC70-4 |
| LTC3413EFE#PBF | IC REG BUCK SYNC ADJ 3A 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1976HFE | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage 1.5A, 200kHz Step-Down Switching Regulator with 100μA Quiescent Current |
| LT1976HFE#PBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1976HFE#TRPBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1976IFE | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1976IFE#PBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。