- 您现在的位置：买卖IC网 > PDF目录14802 > LT1976EFE#PBF (Linear Technology)IC REG BUCK ADJ 1.5A 16TSSOP PDF资料下载
参数资料
| 型号： | LT1976EFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.5A 16TSSOP |
| 标准包装： | 95 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.2 V ~ 54 V |
| 输入电压： | 3.3 V ~ 60 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 200kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-TSSOP-EP |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1976/LT1976B
PI FU CTIO S
C SS (Pin 9): A capacitor from the C SS pin to the regulated
output voltage determines the output voltage ramp rate
during start-up. When the current through the C SS capaci-
tor exceeds the C SS threshold (I CSS ), the voltage ramp of
the output is limited. The C SS threshold is proportional to
the FB voltage (see Typical Performance Characteristics)
and is defeated for FB voltage greater than 0.9V (typical).
See Soft-Start section in Applications Information for
details.
BIAS (Pin 10): The BIAS pin is used to improve efficiency
when operating at higher input voltages and light load
current. Connecting this pin to the regulated output volt-
age forces most of the internal circuitry to draw its
operating current from the output voltage rather than the
input supply. This architecture increases efficiency espe-
cially when the input voltage is much higher than the
output. Minimum output voltage setting for this mode of
operation is 3V.
V C (Pin 11): The V C pin is the output of the error amplifier
and the input of the peak switch current comparator. It is
normally used for frequency compensation, but can also
serve as a current clamp or control loop override. The V C
pin sits about 0.45V for light loads and 2.2V at current
limit. The LT1976 clamps the V C pin slightly below the
burst threshold during sleep periods for better transient
response. Driving the V C pin to ground will disable switch-
ing and also place the LT1976 into sleep mode.
FB (Pin 12): The feedback pin is used to determine the
PGFB (PIN 13): The PGFB pin is the positive input to a
comparator whose negative input is set at V PGFB . When
PGFB is taken above V PGFB , current (I CSS ) is sourced into
the C T pin starting the PG delay period. When the voltage
on the PGFB pin drops below V PGFB , the C T pin is rapidly
discharged resetting the PG delay period. The PGFB volt-
age is typically generated by a resistive divider from the
regulated output or input supply. See Power Good section
in Applications Information for details.
SYNC (Pin 14): The SYNC pin is used to synchronize the
internal oscillator to an external signal. It is directly logic
compatible and can be driven with any signal between
20% and 80% duty cycle. The synchronizing range is
equal to maximum initial operating frequency up to 700kHz.
When the voltage on the FB pin is below 0.9V the SYNC
function is disabled. See the Synchronizing section in
Applications Information for details.
SHDN (Pin 15): The SHDN pin is used to turn off the
regulator and to reduce input current to less than 1 μ A. The
SHDN pin requires a voltage above 1.3V with a typical
source current of 5 μ A to take the IC out of the shutdown
state.
PG (Pin 16): The PG pin is functional only when the SHDN
pin is above its threshold, and is active low when the
internal clamp on the C T pin is below its clamp level and
high impedance when the clamp is active. The PG pin has
a typical sink capability of 200 μ A. See the Power Good
section in Applications Information for details.
output voltage using an external voltage divider from the
output that generates 1.25V at the FB pin . When the FB pin
drops below 0.9V, switching frequency is reduced, the
SYNC function is disabled and output ramp rate control is
enabled via the C SS pin. See the Feedback section in
Applications Information for details.
1976bfg
9
相关PDF资料 |
PDF描述 |
|---|---|
| RBM12DRMN-S664 | CONN EDGECARD 24POS .156 WW |
| LTC3442EDE#PBF | IC REG BUCK BOOST SYNC ADJ 12DFN |
| LT8582EDKD#PBF | IC REG MULTI CONFIG ADJ 3A 24DFN |
| MAX6423XS28+T | IC MPU/RESET CIRC 2.80V SC70-4 |
| LTC3413EFE#PBF | IC REG BUCK SYNC ADJ 3A 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1976HFE | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage 1.5A, 200kHz Step-Down Switching Regulator with 100μA Quiescent Current |
| LT1976HFE#PBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1976HFE#TRPBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1976IFE | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1976IFE#PBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。