- 您现在的位置：买卖IC网 > PDF目录4588 > LT3008MPTS8-2.5#TRPBF (Linear Technology)IC REG LDO 2.5V 20MA TSOT23-8 PDF资料下载
参数资料
| 型号： | LT3008MPTS8-2.5#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.5V 20MA TSOT23-8 |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.5V |
| 输入电压： | 最高 45 V |
| 电压 - 压降（标准）： | 0.3V @ 20mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 20mA |
| 电流 - 限制（最小）： | 22mA |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 薄型，TSOT-23-8 |
| 供应商设备封装： | TSOT-23-8 |
| 包装： | 带卷 (TR) |
LT3008 Series
PIN FUNCTIONS
(TSOT-23/DFN)
SHDN (Pin 1/Pin 5): Shutdown. Pulling the SHDN pin
low puts the LT3008 into a low power state and turns the
output off. If unused, tie the SHDN pin to V IN . The LT3008
does not function if the SHDN pin is not connected. The
SHDN pin cannot be driven below GND unless tied to the
IN pin. If the SHDN pin is driven below GND while IN is
powered, the output will turn on. SHDN pin logic cannot
be referenced to a negative rail.
GND (Pins 2, 3, 4/Pin 6): Ground. Connect the bottom
of the resistor divider that sets output voltage directly to
GND for the best regulation.
IN (Pin 5/Pin 4): Input. The IN pin supplies power to the
device. The LT3008 requires a bypass capacitor at IN if
the device is more than six inches away from the main
input ?lter capacitor. In general, the output impedance of
a battery rises with frequency, so it is advisable to include
a bypass capacitor in battery-powered circuits. A bypass
capacitor in the range of 0.1μF to 10μF will suf?ce. The
LT3008 withstands reverse voltages on the IN pin with
respect to ground and the OUT pin. In the case of a reversed
input, which occurs with a battery plugged in backwards,
the LT3008 acts as if a blocking diode is in series with its
input. No reverse current ?ows into the LT3008 and no
reverse voltage appears at the load. The device protects
both itself and the load.
OUT (Pin 6/Pins 2, 3): Output. This pin supplies power
to the load. Use a minimum output capacitor of 2.2μF
Temperature in the Typical Performance Characteristics
section). The ADJ pin voltage is 600mV referenced to GND
and the output voltage range is 600mV to 44.5V.
NC (Pin 8, TSOT-23 Package Only): No Connect. Pin 8
is an NC pin in the TSOT-23 package. This pin is not tied
to any internal circuitry. It may be ?oated, tied to V IN or
tied to GND.
GND (Exposed Pad Pin 7, DFN Package Only): Ground. The
exposed pad (backside) of the DFN package is an electrical
connection to GND. To ensure optimum performance,
solder Pin 7 to the PCB and tie directly to Pin 6.
SENSE (Pin 7/Pin 1): Sense. For ?xed voltage versions of
the LT3008 (LT3008-1.2, LT3008-1.5, LT3008-1.8, LT3008-
2.5, LT3008-3.3, LT3008-5), the SENSE pin is the input to
the error ampli?er. Optimum regulation is obtained at the
point where the SENSE pin is connected to the OUT pin of
the regulator. In critical applications, small voltage drops
are caused by the resistance (RP) of PC traces between
the regulator and the load. These may be eliminated by
connecting the SENSE pin to the output at the load as
shown in Figure 1 (Kelvin Sense Connection). Note that
the voltage drop across the external PC traces add to the
dropout voltage of the regulator. The SENSE pin bias current
is 1μA at the nominal rated output voltage. The SENSE pin
can be pulled below ground (as in a dual supply system
where the regulator load is returned to a negative supply)
and still allow the device to start and operate.
to prevent oscillations. Large load transient applications
require larger output capacitors to limit peak voltage
IN
OUT
R P
transients. See the Applications Information section for
more information on output capacitance and reverse-output
characteristics.
V IN
+
LT3008
SHDN SENSE
GND
+
LOAD
ADJ (Pin 7/Pin 1): Adjust. This pin is the error ampli?er’s
inverting terminal. Its 400pA typical input bias current
?ows out of the pin (see curve of ADJ Pin Bias Current vs
R P
Figure 1. Kelvin Sense Connection
3008 F01
3008fc
11
相关PDF资料 |
PDF描述 |
|---|---|
| LT3015IQ-12#TRPBF | IC REG LDO -12V 1.5A DDPAK-5 |
| LT3015IQ#TRPBF | IC REG LDO NEG ADJ 1.5A 5DD-PAK |
| LFXP10C-3F256C | IC FPGA 9.7KLUTS 188I/O 256-BGA |
| IDT72V51236L6BB8 | IC FLOW CTRL MULTI QUEUE 256-BGA |
| LFECP10E-3FN484C | IC FPGA 10.2KLUTS 484FPBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3008MPTS8-3.3#TRM | 制造商:Linear Technology 功能描述:Conn Subminiature Cylindrical PIN 42 POS Crimp ST Wall Mount 42 Terminal 1 Port |
| LT3008MPTS8-3.3#TRMPBF | 功能描述:IC REG LDO 3.3V 20MA TSOT23-8 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:2.3 V ~ 5.5 V 电压 - 压降（标准）:0.035V @ 150mA 稳压器数量:2 电流 - 输出:150mA 电流 - 限制（最小）:300mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-UFDFN 裸露焊盘，6-TMLF? 供应商设备封装:6-TMLF?（1.6x1.6） 包装:Digi-Reel® 产品目录页面:1104 (CN2011-ZH PDF) 其它名称:576-3018-6 |
| LT3008MPTS8-3.3#TRPBF | 功能描述:IC REG LDO 3.3V 20MA TSOT23-8 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:2.3 V ~ 5.5 V 电压 - 压降（标准）:0.035V @ 150mA 稳压器数量:2 电流 - 输出:150mA 电流 - 限制（最小）:300mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-UFDFN 裸露焊盘，6-TMLF? 供应商设备封装:6-TMLF?（1.6x1.6） 包装:Digi-Reel® 产品目录页面:1104 (CN2011-ZH PDF) 其它名称:576-3018-6 |
| LT3008MPTS8-5#PBF | 制造商:Linear Technology 功能描述:SP-LINREG, Cut Tape 3uA Iq, 20mA Low Dropout Linear Regulators |
| LT3008MPTS8-5#TRMPBF | 功能描述:IC REG LDO 5V 20MA TSOT23-8 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:2.3 V ~ 5.5 V 电压 - 压降（标准）:0.035V @ 150mA 稳压器数量:2 电流 - 输出:150mA 电流 - 限制（最小）:300mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-UFDFN 裸露焊盘，6-TMLF? 供应商设备封装:6-TMLF?（1.6x1.6） 包装:Digi-Reel® 产品目录页面:1104 (CN2011-ZH PDF) 其它名称:576-3018-6 |
发布紧急采购，3分钟左右您将得到回复。