参数资料
| 型号： | LT3013MPFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/20页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .25A 16-TSSOP |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 95 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.24 V ~ 60 V |
| 输入电压： | 4 V ~ 80 V |
| 电压 - 压降（标准）： | 0.4V @ 250mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 250mA |
| 电流 - 限制（最小）： | 250mA |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 管件 |
LT3013
APPLICATIONS INFORMATION
In situations where the ADJ pin is connected to a resistor
divider that would pull the ADJ pin above its 7V clamp
voltage if the output is pulled high, the ADJ pin input current
must be limited to less than 5mA. For example, a resistor
divider is used to provide a regulated 1.5V output from the
1.24V reference when the output is forced to 60V. The top
resistor of the resistor divider must be chosen to limit the
current into the ADJ pin to less than 5mA when the ADJ
pin is at 7V. The 53V difference between the OUT and ADJ
pins divided by the 5mA maximum current into the ADJ
pin yields a minimum top resistor value of 10.6k.
In circuits where a backup battery is required, several
different input/output conditions can occur. The output
voltage may be held up while the input is either pulled
to ground, pulled to some intermediate voltage, or is left
open-circuit. Current ?ow back into the output will follow
the curve shown in Figure 5. The rise in reverse output
current above 7V occurs from the breakdown of the 7V
clamp on the ADJ pin. With a resistor divider on the
regulator output, this current will be reduced depending
on the size of the resistor divider.
When the IN pin of the LT3013 is forced below the OUT
pin or the OUT pin is pulled above the IN pin, input current
will typically drop to less than 2μA. This can happen if
the input of the LT3013 is connected to a discharged
(low voltage) battery and the output is held up by either
a backup battery or a second regulator circuit. The state
of the SHDN pin will have no effect on the reverse output
current when the output is pulled above the input.
200
T J = 25°C
180 V IN = 0V
160
140
120
V OUT = V ADJ
100
80
60
40
20
CURRENT FLOWS
INTO OUTPUT PIN
ADJ
PIN CLAMP
(SEE ABOVE)
0
0
1
2
3
4
5
6 7
8
9
10
OUTPUT VOLTAGE (V)
3013 F05
Figure 5. Reverse Output Current
3013fe
17
相关PDF资料 |
PDF描述 |
|---|---|
| LT3014HVIS5#TRPBF | IC REG LDO ADJ 20MA SOT23-5 |
| LT3015MPQ-5#TRPBF | IC REG LDO -5V 1.5A DDPAK-5 |
| LT3020IDD#TRPBF | IC REG LDO ADJ .1A 8-DFN |
| LT3021IS8-1.8#TRPBF | IC REG LDO 1.8V .5A 8-SOIC |
| LT3022EMSE-1.5#PBF | IC REG LDO 1.5V 1A 16MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3014 | 制造商:LINER 制造商全称:Linear Technology 功能描述:20mA, 3V to 80V Low Dropout Micropower Linear Regulator |
| LT3014B | 制造商:LINER 制造商全称:Linear Technology 功能描述:20mA, 3V to 80V Low Dropout Micropower Linear Regulator |
| LT3014BEDD | 制造商:Linear Technology 功能描述:LDO Regulator Pos 1.22V to 60V 0.02A 8-Pin DFN EP |
| LT3014BEDD#PBF | 功能描述:IC REG LDO ADJ 20MA 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| LT3014BEDD#PBF | 制造商:Linear Technology 功能描述:LDO ADJ 1.22V TO 60V 20mA DFN-8 制造商:Linear Technology 功能描述:LDO, ADJ, 1.22V TO 60V, 20mA, DFN-8 |
发布紧急采购，3分钟左右您将得到回复。