参数资料
| 型号： | LT3020EMS8-1.8#TR |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V .1A 8MSOP |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 最高 10V |
| 电压 - 压降（标准）： | 0.15V @ 100mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 100mA |
| 电流 - 限制（最小）： | 110mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
LT3020/LT3020-1.2/
LT3020-1.5/LT3020-1.8
APPLICATIO S I FOR ATIO
response to light tapping from a pencil. Similar vibration
induced behavior can masquerade as increased output
voltage noise.
No-Load/Light-Load Recovery
A possible transient load step that occurs is where the
output current changes from its maximum level to zero
current or a very small load current. The output voltage
responds by overshooting until the regulator lowers the
amount of current it delivers to the new level. The regulator
loop response time and the amount of output capacitance
control the amount of overshoot. Once the regulator has
decreased its output current, the current provided by the
resistor divider (which sets V OUT ) is the only current
remaining to discharge the output capacitor from the level
to which it overshot. The amount of time it takes for the
output voltage to recover easily extends to milliseconds
with microamperes of divider current and a few microfar-
ads of output capacitance.
To eliminate this problem, the LT3020 incorporates a
no-load or light-load recovery circuit. This circuit is a
voltage-controlled current sink that significantly improves
the light load transient response time by discharging the
output capacitor quickly and then turning off. The current
sink turns on when the output voltage exceeds 6% of the
nominal output voltage. The current sink level is then
proportional to the overdrive above the threshold up to a
maximum of approximately 15mA. Consult the curve in
the Typical Performance Characteristics for the No-Load
Recovery Threshold.
If external circuitry forces the output above the no load
recovery circuit’s threshold, the current sink turns on in an
attempt to restore the output voltage to nominal. The
current sink remains on until the external circuitry releases
the output. However, if the external circuitry pulls the
output voltage above the input voltage, or the input falls
below the output, the LT3020 turns the current sink off and
1. Output current multiplied by the input-to-output volt-
age differential: (I OUT )(V IN – V OUT ) and
2. GND pin current multiplied by the input voltage:
(I GND )(V IN ).
GND pin current is found by examining the GND pin
current curves in the Typical Performance Characteristics.
Power dissipation is equal to the sum of the two compo-
nents listed above.
The LT3020 regulator has internal thermal limiting (with
hysteresis) designed to protect the device during overload
conditions. For normal continuous conditions, do not
exceed the maximum junction temperature rating of 125 ° C.
Carefully consider all sources of thermal resistance from
junction to ambient including other heat sources mounted
in proximity to the LT3020.
The underside of the LT3020 DD package has exposed metal
(4mm 2 ) from the lead frame to where the die is attached.
This allows heat to directly transfer from the die junction
to the printed circuit board metal to control maximum
operating junction temperature. The dual-in-line pin ar-
rangement allows metal to extend beyond the ends of the
package on the topside (component side) of a PCB. Con-
nect this metal to GND on the PCB. The multiple IN and OUT
pins of the LT3020 also assist in spreading heat to the PCB.
The LT3020 MS8 package has pin 4 fused with the lead
frame. This also allows heat to transfer from the die to the
printed circuit board metal, therefore reducing the thermal
resistance. Copper board stiffeners and plated through-
holes can also be used to spread the heat generated by
power devices.
The following tables list thermal resistance for several
different board sizes and copper areas for two different
packages. Measurements were taken in still air on 3/32"
FR-4 board with one ounce copper.
Table 1. Measured Thermal Resistance for DD Package
shuts down the bias current/reference generator circuitry.
COPPER AREA
TOPSIDE* BACKSIDE
BOARD AREA
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
900mm
100mm
2500mm
2500mm
2500mm
2500mm
Thermal Considerations
The LT3020’s power handling capability is limited by its
maximum rated junction temperature of 125 ° C. The power
dissipated by the device is comprised of two components:
2500mm 2
2
225mm 2
2
50mm 2
2500mm 2
2
2500mm 2
2
2500mm 2
2500mm 2
2
2500mm 2
2
2500mm 2
35 ° C/W
40 ° C/W
55 ° C/W
60 ° C/W
70 ° C/W
3020fc
11
相关PDF资料 |
PDF描述 |
|---|---|
| LT3020EMS8-1.5#TR | IC REG LDO 1.5V .1A 8MSOP |
| LT3020EMS8#TRPBF | IC REG LDO ADJ .1A 8-MSOP |
| LT3020EMS8#TR | IC REG LDO ADJ .1A 8MSOP |
| LT3020EDD-1.5#TRPBF | IC REG LDO 1.5V .1A 8-DFN |
| LT3020EDD-1.5#TR | IC REG LDO 1.5V .1A 8-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3020EMS8PBF | 制造商:Linear Technology 功能描述:LT3020 adjustable 100mA LDO regulator |
| LT3020IDD | 制造商:Linear Technology 功能描述:LDO Regulator Pos 0.2V to 9.5V 0.1A 8-Pin DFN EP |
| LT3020IDD#PBF | 功能描述:IC REG LDO ADJ .1A 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:MIC5365/66 Ultra-small LDO Regulators 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.155V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:200mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UDFN 裸露焊盘，4-TMLF? 供应商设备封装:4-TMLF?（1x1） 包装:Digi-Reel® 其它名称:576-3192-6 |
| LT3020IDD#TRPBF | 功能描述:IC REG LDO ADJ .1A 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| LT3020IDD-1.2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:100mA, Low Voltage, Very Low Dropout Linear Regulator |
发布紧急采购，3分钟左右您将得到回复。