参数资料
| 型号： | LT3027IDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .1A 10-DFN |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.22 V ~ 20 V |
| 输入电压： | 1.8 V ~ 20 V |
| 电压 - 压降（标准）： | 0.3V @ 100mA |
| 稳压器数量： | 2 |
| 电流 - 输出： | 100mA |
| 电流 - 限制（最小）： | 110mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 带卷 (TR) |
LT3027
APPLICATIO S I FOR ATIO
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress,
similar to the way a piezoelectric accelerometer or
microphone works. For a ceramic capacitor the stress
can be induced by vibrations in the system or thermal
transients. The resulting voltages produced can cause
appreciable amounts of noise, especially when a ceramic
capacitor is used for noise bypassing. A ceramic capaci-
tor produced Figure 5’s trace in response to light tapping
from a pencil. Similar vibration induced behavior can
masquerade as increased output voltage noise.
C OUT = 10 μ F
C BYP = 0.01 μ F
I LOAD = 100mA
For continuous normal conditions, the maximum junction
temperature rating of 125 ° C must not be exceeded. It is
important to give careful consideration to all sources of
thermal resistance from junction to ambient. Additional
heat sources mounted nearby must also be considered.
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holes can also be used to spread the heat gener-
ated by power devices.
The following tables list thermal resistance for several
different board sizes and copper areas. All measurements
were taken in still air on 3/32" FR-4 board with one ounce
copper.
Table 1. MSE Package, 10-Lead MSOP
V OUT
500 μ V/DIV
COPPER AREA
TOPSIDE* BACKSIDE
BOARD AREA
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
2500mm 2
2500mm 2
2500mm 2
40 ° C/W
1000mm
2500mm
2
2500mm
2
2
45 ° C/W
2500mm
225mm
2
2500mm
2
2
50 ° C/W
2500mm
100ms/DIV
3027 F05
100mm
2
2500mm
2
2
62 ° C/W
Figure 5. Noise Resulting from Tapping on a Ceramic Capacitor
*Device is mounted on topside.
Thermal Considerations
Table 2. DD Package, 10-Lead DFN
COPPER AREA
THERMAL RESISTANCE
1000mm
2500mm
2500mm
The power handling capability of the device will be limited
by the maximum rated junction temperature (125 ° C). The
power dissipated by the device will be made up of two
TOPSIDE* BACKSIDE
2500mm 2 2500mm 2
2 2
BOARD AREA
2500mm 2
2
(JUNCTION-TO-AMBIENT)
40 ° C/W
45 ° C/W
2500mm
components (for each channel):
225mm
2
2500mm
2
2
50 ° C/W
1. Output current multiplied by the input/output voltage
100mm 2
2500mm 2
2500mm 2
62 ° C/W
differential: (I OUT )(V IN – V OUT ), and
2. GND pin current multiplied by the input voltage:
(I GND )(V IN ).
The ground pin current can be found by examining the
GND Pin Current curves in the Typical Performance
Characteristics section. Power dissipation will be equal to
the sum of the two components listed above. Power
dissipation from both channels must be considered dur-
ing thermal analysis.
The LT3027 regulator has internal thermal limiting de-
signed to protect the device during overload conditions.
*Device is mounted on topside.
The thermal resistance juncton-to-case ( θ JC ), measured
at the Exposed Pad on the back of the die is 10 ° C/W for the
10-lead MS package and 3 ° C for the 10-lead DFN package.
Calculating Junction Temperature
Example: Given an output voltage on the first channel of
3.3V, an output voltage of 2.5V on the second channel, an
input voltage range of 4V to 6V, output current ranges of
0mA to 100mA for the first channel and 0mA to 50mA for
the second channel, with a maximum ambient temperature
of 50 ° C, what will the maximum junction temperature be?
3027fa
11
相关PDF资料 |
PDF描述 |
|---|---|
| LT3028IDHC#TRPBF | IC REG LDO ADJ .5A/.1A 16-DFN |
| LT3029MPMSE#TRPBF | IC REG LDO ADJ .5A 16MSOP |
| LT3032MPDE-5#TRPBF | IC REG LDO +-5V .15A 14-DFN |
| LT3050MPMSE-5#TRPBF | IC REG LDO 5V .1A 12-MSOP |
| LT3060MPTS8-5#TRPBF | IC REG LDO 5V .1A TSOT23-8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3027IMSE | 制造商:Linear Technology 功能描述:LDO Regulator Pos 1.22V to 20V1.22V to 20V 0.1A/0.1A 10-Pin MSOP EP |
| LT3027IMSE#PBF | 功能描述:IC REG LDO ADJ .1A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| LT3027IMSE#TRPBF | 功能描述:IC REG LDO ADJ .1A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| LT3028 | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.1A, Low Noise, Low Dropout Linear Regulator |
| LT3028EDHC | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 100mA/500mA Low Dropout, Low Noise,Micropower Regulators with Independent Inputs |
发布紧急采购，3分钟左右您将得到回复。