参数资料
| 型号： | LT3029IMSE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .5A 16MSOP |
| 产品培训模块： | LT3029 - 500mA, Dual Output, 1.2 ~ 19.5V, Linear Regulator |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.215 V ~ 19.5 V |
| 输入电压： | 1.8 V ~ 20 V |
| 电压 - 压降（标准）： | 0.3V @ 500mA |
| 稳压器数量： | 2 |
| 电流 - 输出： | 500mA |
| 电流 - 限制（最小）： | 520mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
| 包装： | 带卷 (TR) |
LT3029
APPLICATIONS INFORMATION
Table 2. DE Package, 16-Lead DFN
The thermal resistance is in the range of 35°C/W to 40°C/W,
COPPER AREA
TOPSIDE * BACKSIDE
THERMAL RESISTANCE
BOARD AREA (JUNCTION-TO-AMBIENT)
depending on the copper area. So, the junction temperature
rise above ambient temperature approximately equals:
2500mm 2
1000mm 2
225mm 2
100mm 2
2500mm 2
2500mm 2
2500mm 2
2500mm 2
2500mm 2
2500mm 2
2500mm 2
2500mm 2
36°C/W
37°C/W
38°C/W
40°C/W
(0.37W + 0.52W) 39°C/W = 34.7°C
The maximum junction temperature then equals the maxi-
mum ambient temperature plus the maximum junction
temperature rise above ambient temperature, or:
*Device is mounted on topside.
Table 3. MSE Package, 16-Lead MSOP
T JMAX = 50°C + 34.7°C = 84.7°C
COPPER AREA
THERMAL RESISTANCE
Protection Features
TOPSIDE *
2500mm 2
1000mm 2
225mm 2
100mm 2
BACKSIDE
2500mm 2
2500mm 2
2500mm 2
2500mm 2
BOARD AREA (JUNCTION-TO-AMBIENT)
2500mm 2 35°C/W
2500mm 2 36°C/W
2500mm 2 37°C/W
2500mm 2 39°C/W
The LT3029 regulator incorporates several protection fea-
tures that make it ideal for use in battery-powered circuits.
In addition to the normal protection features associated
with monolithic regulators, such as current limiting and
thermal limiting, the device protects itself against reverse
*Device is mounted on topside.
The junction-to-case thermal resistance ( θ JC ), measured
at the Exposed Pad on the back of the die, is 4.3°C/W for
the DFN package, and 5°C/W to 10°C/W for the MSOP
package.
Calculating Junction Temperature
Example: Channel 1’s output voltage is set to 1.8V. Chan-
nel 2’s output voltage is set to 1.5V. Each channel’s input
voltage is 2.5V. Each channel’s output current range is
0mA to 500mA. The application has a maximum ambient
temperature of 50°C. What is the LT3029’s maximum
junction temperature?
The power dissipated by each channel equals:
I OUT(MAX) (V IN – V OUT ) + I GND (V IN )
where for each output:
I OUT(MAX) = 500mA
V IN = 2.5V
I GND at (I OUT = 500mA, V IN = 2.5V) = 8.5mA
So, for output 1:
P = 500mA (2.5V – 1.8V) + 8.5mA (2.5V) = 0.37W
For output 2:
P = 500mA (2.5V – 1.5V) + 8.5mA (2.5V) = 0.52W
input voltages and reverse voltages from output to input.
The two regulators have independent inputs, a common
GND pin and are thermally coupled. However, the two
channels of the LT3029 operate independently. Each
channel’s output can be shut down independently, and
a fault condition on one output does not affect the other
output electrically, unless the thermal shutdown circuitry
is activated.
Current limit protection and thermal overload protection
protect the device against current overload conditions at
each output of the LT3029. For normal operation, do not
allow the junction temperature to exceed 125°C (LT3029E/
LT3029I/LT3029MP) or 150°C (LT3029H). The typical ther-
mal shutdown temperature threshold is 165°C and the
circuitry incorporates approximately 5°C of hysteresis.
Each channel’s input withstands reverse voltages of 22V.
Current ?ow into the device is limited to less than 1mA
(typically less than 100μA) and no negative voltage appears
at the respective channel’s output. The device protects
both itself and the load against batteries that are plugged
in backwards.
The LT3029 incurs no damage if either channel’s output
is pulled below ground. If the input is left open-circuit, or
grounded, the output can be pulled below ground by 22V.
The output acts like an open circuit, and no current ?ows
from the output. However, current ?ows in (but is limited
by) the external resistor divider that sets the output voltage.
3029fa
15
相关PDF资料 |
PDF描述 |
|---|---|
| ESM36DRMI | CONN EDGECARD 72POS .156 SQ WW |
| HBC40DRYS-S93 | CONN EDGECARD 80POS DIP .100 SLD |
| FMC06DRES-S93 | CONN EDGECARD 12POS .100 EYELET |
| ESC50DREN-S93 | CONN EDGECARD 100POS .100 EYELET |
| ESC50DREH-S93 | CONN EDGECARD 100POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3029MPMSE | 功能描述:IC REG LDO ADJ .5A 16MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:4V 输入电压:最高 16V 电压 - 压降（标准）:0.28V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:5-VFBGA 供应商设备封装:5-uSMD 包装:Digi-Reel® 其它名称:LP2985AIBP-4.0DKR |
| LT3029MPMSE#PBF | 功能描述:IC REG LDO ADJ .5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| LT3029MPMSE#PBF | 制造商:Linear Technology 功能描述:LDO REGULATOR IC |
| LT3029MPMSE#TR | 功能描述:IC REG LDO ADJ .5A 16MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:4V 输入电压:最高 16V 电压 - 压降（标准）:0.28V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:5-VFBGA 供应商设备封装:5-uSMD 包装:Digi-Reel® 其它名称:LP2985AIBP-4.0DKR |
| LT3029MPMSE#TRPBF | 功能描述:IC REG LDO ADJ .5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。