参数资料
| 型号： | LT3029IMSE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/20页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .5A 16MSOP |
| 产品培训模块： | LT3029 - 500mA, Dual Output, 1.2 ~ 19.5V, Linear Regulator |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.215 V ~ 19.5 V |
| 输入电压： | 1.8 V ~ 20 V |
| 电压 - 压降（标准）： | 0.3V @ 500mA |
| 稳压器数量： | 2 |
| 电流 - 输出： | 500mA |
| 电流 - 限制（最小）： | 520mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
| 包装： | 带卷 (TR) |
LT3029
ELECTRICAL CHARACTERISTICS The l denotes the speci?cations which apply over the full operating
temperature range, otherwise speci?cations are at T A = 25°C. (Note 2)
PARAMETER
Minimum Input Voltage (Notes 3, 11)
CONDITIONS
I LOAD = 500mA
l
MIN
TYP
1.8
MAX
2.3
UNITS
V
ADJ1, ADJ2 Pin Voltage (Notes 3, 4, 9)
Line Regulation (Note 3)
Load Regulation (Note 3)
Dropout Voltage
V IN = V OUT(NOMINAL)
(Notes 5, 6, 11)
GND Pin Current (per Channel)
V IN = V OUT(NOMINAL)
(Notes 5, 7)
V IN = 2V, I LOAD = 1mA
2.3V < V IN < 20V, 1mA < I LOAD < 500mA (E, I, MP)
2.3V < V IN < 20V, 1mA < I LOAD < 500mA (H)
ΔV IN = 2V to 20V, I LOAD = 1mA
V IN = 2.3V, ΔI LOAD = 1mA to 500mA
V IN = 2.3V, ΔI LOAD = 1mA to 500mA (E, I, MP)
V IN = 2.3V, ΔI LOAD = 1mA to 500mA (H)
I LOAD = 10mA
I LOAD = 10mA
I LOAD = 50mA
I LOAD = 50mA
I LOAD = 100mA
I LOAD = 100mA
I LOAD = 500mA
I LOAD = 500mA
I LOAD = 0mA
I LOAD = 1mA
I LOAD = 50mA
I LOAD = 100mA
I LOAD = 250mA
I LOAD = 500mA
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
1.203
1.191
1.173
1.215
1.215
1.215
0.5
2.5
0.11
0.16
0.2
0.3
55
90
1.1
2
4.3
10
1.227
1.239
1.239
5
6
15
32
0.18
0.25
0.22
0.31
0.25
0.34
0.36
0.46
150
250
2
3.5
8
16
V
V
V
mV
mV
mV
mV
V
V
V
V
V
V
V
V
μA
μA
mA
mA
mA
mA
Output Voltage Noise
C OUT = 10μF, C BYP = 10nF, I LOAD = 500mA,
20
μV RMS
BW = 10Hz to 100kHz
ADJ1/ADJ2 Pin Bias Current
ADJ1, ADJ2 (Notes 3, 8)
30
100
nA
Shutdown Threshold
SHDN1 / SHDN2 Pin Current (Note 10)
Quiescent Current in Shutdown (per Channel)
Ripple Rejection
V OUT = Off to On
V OUT = On to Off
V SHDN1 , V SHDN2 = 0V
V SHDN1 , V SHDN2 = 20V
V IN = 6V, V SHDN1 = 0V, V SHDN2 = 0V
V IN = 2.715V (Avg), V RIPPLE = 0.5V P-P ,
l
l
l
l
0.20
55
0.45
0.40
0
0.6
0.01
67
1.1
0.5
3
0.1
V
V
μA
μA
μA
dB
f RIPPLE = 120Hz, I LOAD = 500mA
Current Limit (Note 9)
V IN = 7V, V OUT = 0V
V IN = 2.3V, ΔV OUT = –0.1V
l
520
1.5
A
mA
Input Reverse Leakage Current
Reverse Output Current
V IN = –20V, V OUT = 0V
V OUT = 1.215V, V IN = 0V
l
0.5
1
10
mA
μA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3029 is tested and speci?ed under pulse load conditions
such that T J ≈ T A . The LT3029E is 100% tested at T A = 25°C. Performance
of the LT3029E over the full –40°C to 125°C operating junction
temperature range is assured by design, characterization and correlation
with statistical process controls. The LT3029I is guaranteed over the full
–40°C to 125°C operating junction temperature range. The LT3029MP is
100% tested and guaranteed over the –55°C to 125°C operating junction
temperature range. The LT3029H is tested at 150°C operating junction
temperature. High junction temperatures degrade operating lifetimes.
Operating lifetime is derated at junction temperatures greater than 125°C.
Note 3: The LT3029 is tested and speci?ed for these conditions with the
ADJ1/ADJ2 pin connected to the corresponding OUT1/OUT2 pin.
Note 4: Maximum junction temperature limits operating conditions. The
regulated output voltage speci?cation does not apply for all possible
combinations of input voltage and output current. When operating at
maximum input voltage, limit the output current range. When operating at
maximum output current, limit the input voltage range.
Note 5: To satisfy minimum input voltage requirements, the LT3029 is
tested and speci?ed for these conditions with an external resistor divider
(two 243k resistors) for an output voltage of 2.437V. The external resistor
divider adds 5μA of DC load on the output.
Note 6: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a speci?ed output current. In dropout, the
output voltage equals: V IN – V DROPOUT .
3029fa
3
相关PDF资料 |
PDF描述 |
|---|---|
| ESM36DRMI | CONN EDGECARD 72POS .156 SQ WW |
| HBC40DRYS-S93 | CONN EDGECARD 80POS DIP .100 SLD |
| FMC06DRES-S93 | CONN EDGECARD 12POS .100 EYELET |
| ESC50DREN-S93 | CONN EDGECARD 100POS .100 EYELET |
| ESC50DREH-S93 | CONN EDGECARD 100POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3029MPMSE | 功能描述:IC REG LDO ADJ .5A 16MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:4V 输入电压:最高 16V 电压 - 压降（标准）:0.28V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:5-VFBGA 供应商设备封装:5-uSMD 包装:Digi-Reel® 其它名称:LP2985AIBP-4.0DKR |
| LT3029MPMSE#PBF | 功能描述:IC REG LDO ADJ .5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| LT3029MPMSE#PBF | 制造商:Linear Technology 功能描述:LDO REGULATOR IC |
| LT3029MPMSE#TR | 功能描述:IC REG LDO ADJ .5A 16MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:4V 输入电压:最高 16V 电压 - 压降（标准）:0.28V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:5-VFBGA 供应商设备封装:5-uSMD 包装:Digi-Reel® 其它名称:LP2985AIBP-4.0DKR |
| LT3029MPMSE#TRPBF | 功能描述:IC REG LDO ADJ .5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。