- 您现在的位置：买卖IC网 > PDF目录80082 > LT3407EDD-2 (LINEAR TECHNOLOGY CORP) 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | LT3407EDD-2 |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | 3 X 3 MM, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件页数： | 15/16页 |
| 文件大小： | 221K |
| 代理商： | LT3407EDD-2 |
LTC3407-2
8
34072fa
Table 1. Representative Surface Mount Inductors
PART
VALUE
DCR
MAX DC
SIZE
NUMBER
(
μH)
(
Ω MAX) CURRENT (A) W × L × H (mm3)
Sumida
2.2
0.075
1.20
3.8
× 3.8 × 1.8
CDRH3D16
3.3
0.110
1.10
4.7
0.162
0.90
Sumida
1.5
0.068
0.900
3.2
× 3.2 × 1.2
CDRH2D11
2.2
0.170
0.780
Sumida
2.2
0.116
0.950
4.4
× 5.8 × 1.2
CMD4D11
3.3
0.174
0.770
Murata
1.0
0.060
1.00
2.5
× 3.2 × 2.0
LQH32CN
2.2
0.097
0.79
Toko
2.2
0.060
1.08
2.5
× 3.2 × 2.0
D312F
3.3
0.260
0.92
Panasonic
3.3
0.17
1.00
4.5
× 5.4 × 1.2
ELT5KT
4.7
0.20
0.95
Output Capacitor (COUT) Selection
The selection of COUT is driven by the required ESR to
minimize voltage ripple and load step transients. Typically,
once the ESR requirement is satisfied, the capacitance is
adequate for filtering. The output ripple (
ΔVOUT) is deter-
mined by:
Δ≈ Δ
+
V
I ESR
fC
OUT
L
O
OUT
1
8
where f = operating frequency, COUT = output capacitance
and
ΔIL = ripple current in the inductor. The output ripple
is highest at maximum input voltage since
ΔIL increases
with input voltage. With
ΔIL = 0.3 ILIM the output ripple
will be less than 100mV at maximum VIN and fO = 2.25MHz
with:
ESRCOUT < 150mΩ
Once the ESR requirements for COUT have been met, the
RMS current rating generally far exceeds the IRIPPLE(P-P)
requirement, except for an all ceramic solution.
In surface mount applications, multiple capacitors may
have to be paralleled to meet the capacitance, ESR or RMS
current handling requirement of the application. Alumi-
num electrolytic, special polymer, ceramic and dry tantulum
capacitors are all available in surface mount packages. The
OS-CON semiconductor dielectric capacitor available from
Sanyo has the lowest ESR(size) product of any aluminum
electrolytic at a somewhat higher price. Special polymer
begins when the peak inductor current falls below a level
set by the burst clamp. Lower inductor values result in
higher ripple current which causes this to occur at lower
load currents. This causes a dip in efficiency in the upper
range of low current operation. In Burst Mode operation,
lower inductance values will cause the burst frequency to
increase.
Inductor Core Selection
Different core materials and shapes will change the size/
current and price/current relationship of an inductor.
Toroid or shielded pot cores in ferrite or permalloy mate-
rials are small and don’t radiate much energy, but gener-
ally cost more than powdered iron core inductors with
similar electrical characterisitics. The choice of which
style inductor to use often depends more on the price vs
size requirements and any radiated field/EMI require-
ments than on what the LTC3407-2 requires to operate.
Table 1 shows some typical surface mount inductors that
work well in LTC3407-2 applications.
Input Capacitor (CIN) Selection
In continuous mode, the input current of the converter is
a square wave with a duty cycle of approximately VOUT/
VIN. To prevent large voltage transients, a low equivalent
series resistance (ESR) input capacitor sized for the maxi-
mum RMS current must be used. The maximum RMS
capacitor current is given by:
II
VV
V
RMS
MAX
OUT
IN
OUT
IN
≈
(–
)
where the maximum average output current IMAX equals
the peak current minus half the peak-to-peak ripple cur-
rent, IMAX = ILIM – ΔIL/2.
This formula has a maximum at VIN = 2VOUT, where IRMS
= IOUT/2. This simple worst-case is commonly used to
design because even significant deviations do not offer
much relief. Note that capacitor manufacturer’s ripple
current ratings are often based on only 2000 hours life-
time. This makes it advisable to further derate the capaci-
tor, or choose a capacitor rated at a higher temperature
than required. Several capacitors may also be paralleled to
meet the size or height requirements of the design. An
additional 0.1
μF to 1μF ceramic capacitor is also recom-
mended on VIN for high frequency decoupling, when not
using an all ceramic capacitor solution.
APPLICATIO S I FOR ATIO
WU
U
相关PDF资料 |
PDF描述 |
|---|---|
| LT3407EMSE-2 | 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10 |
| LES25A48-2V5RAJ | 1-OUTPUT 62.5 W DC-DC REG PWR SUPPLY MODULE |
| LES25A48-3V3RAJ | 1-OUTPUT 82.5 W DC-DC REG PWR SUPPLY MODULE |
| LT3467AIS67#TR | 2.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LKP5660-5EPD6TB1 | 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT340Z | 制造商:SEOUL 制造商全称:Seoul Semiconductor 功能描述:GREEN OVAL LAMP LED |
| LT341 | 制造商:SEOUL 制造商全称:Seoul Semiconductor 功能描述:BLUE OVAL LAMP LED |
| LT3412G | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LT341BC | 制造商:Datak Corporation 功能描述: |
| LT341L | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
发布紧急采购，3分钟左右您将得到回复。