- 您现在的位置：买卖IC网 > PDF目录13833 > LT3435IFE#PBF (Linear Technology)IC REG BUCK ADJ 3A 16TSSOP PDF资料下载
参数资料
| 型号： | LT3435IFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3A 16TSSOP |
| 标准包装： | 95 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.25 V ~ 54 V |
| 输入电压： | 3.3 V ~ 60 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-TSSOP-EP |
LT3435
APPLICATIO S I FOR ATIO
If a no load condition can be anticipated, the supply current
can be further reduced by cycling the SHDN pin at a rate
Table 4. Catch Diode Selection Criteria
I Q at 125 ° C EFFICIENCY
higher than the natural no load burst frequency. Figure 6
shows Burst Mode operation with the SHDN pin. V OUT
burst ripple is maintained while the average supply current
drops to 15 μ A. The PG pin will be active low during the
“on” portion of the SHDN waveform due to the C T capaci-
tor discharge when SHDN is taken low. See the Power
Good section for further information.
DIODE
IR 10BQ100
Diodes Inc.
B260SMA
Diodes Inc.
B360SMB
LEAKAGE
V OUT = 3.3V V F AT 1A
25 ° C 125 ° C 25 ° C 125 ° C
0.0 μ A 59 μ A 0.72V 0.58V
0.1 μ A 242 μ A 0.48V 0.41V
0.2 μ A 440 μ A 0.45V 0.36V
V IN =12V V IN =12V
V OUT = 3.3 V OUT = 3.3V
I L = 0A I L = 1A
125 μ A 74.7%
215 μ A 81.7%
270 μ A 82.4%
IR
1 μ A
1.81mA 0.42V
0.34V
821 μ A
82.7%
V OUT
50mV/DIV
AC-COUPLED
MBRS360TR
IR 30BQ100
1.7 μ A 2.64mA 0.40V
0.32V
1088 μ A
81.1%
lack of a significant reverse recovery time. Schottky diodes
V SHDN
2V/DIV
I SW
1A/DIV
are generally available with reverse voltage ratings of 60V
and even 100V and are price competitive with other types.
The effect of reverse leakage and forward drop on effi-
ciency for various Schottky diodes is shown in Table 4. As
V IN = 12V
V OUT = 3.3V
I Q = 15μA
100ms/DIV
3435 F06
can be seen these are conflicting parameters and the user
must weigh the importance of each specification in choos-
ing the best diode for the application.
Figure 6. Burst Mode with Shutdown Pin
CATCH DIODE
The catch diode carries load current during the SW off
time. The average diode current is therefore dependent on
the switch duty cycle. At high input to output voltage ratios
the diode conducts most of the time. As the ratio ap-
proaches unity the diode conducts only a small fraction of
the time. The most stressful condition for the diode is
when the output is short circuited. Under this condition the
diode must safely handle I PEAK at maximum duty cycle.
To maximize high and low load current efficiency a fast
switching diode with low forward drop and low reverse
leakage should be used. Low reverse leakage is critical to
maximize low current efficiency since its value over tem-
perature can potentially exceed the magnitude of the
LT3435 supply current. Low forward drop is critical for
high current efficiency since the loss is proportional to
forward drop.
These requirements result in the use of a Schottky type
diode. DC switching losses are minimized due to its low
forward voltage drop and AC behavior is benign due to its
The use of so-called “ultrafast” recovery diodes is gener-
ally not recommended. When operating in continuous
mode, the reverse recovery time exhibited by “ultrafast”
diodes will result in a slingshot type effect. The power
internal switch will ramp up V IN current into the diode in an
attempt to get it to recover. Then, when the diode has
finally turned off, some tens of nanoseconds later, the V SW
node voltage ramps up at an extremely high dV/dt, per-
haps 5V to even 10V/ns! With real world lead inductances
the V SW node can easily overshoot the V IN rail. This can
result in poor RFI behavior and, if the overshoot is severe
enough, damage the IC itself.
BOOST PIN
For most applications the boost components are a 0.33 μ F
capacitor and a MMSD914 diode. The anode is typically
connected to the regulated output voltage to generate a
voltage approximately V OUT above V IN to drive the output
stage (Figure 7a). However, the output stage discharges
the boost capacitor during the on time of the switch. The
output driver requires at least 2.5V of headroom through-
out this period to keep the switch fully saturated. If the
3435fa
16
相关PDF资料 |
PDF描述 |
|---|---|
| LT1370HVCT7 | IC REG MULTI CONFIG ADJ TO220-7 |
| LT1074IT | IC REG MULTI CONFIG ADJ TO220-5 |
| L04026R8BHLTR | INDUCTOR THIN FILM 6.8NH 0402 |
| L04025R6BHLTR | INDUCTOR THIN FILM 5.6NH 0402 |
| LT1076HVCT7-5 | IC REG MULTI CONFIG 5V TO220-7 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3436 | 制造商:LINER 制造商全称:Linear Technology 功能描述:3A, 800kHz Step-Up Switching Regulator |
| LT3436EFE | 功能描述:IC REG BOOST ADJ 3A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3436EFE#PBF | 功能描述:IC REG BOOST ADJ 3A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3436EFE#TR | 功能描述:IC REG BOOST ADJ 3A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3436EFE#TRPBF | 功能描述:IC REG BOOST ADJ 3A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。