- 您现在的位置：买卖IC网 > PDF目录20772 > LT3478EFE#PBF (Linear Technology)IC LED DRVR HP CONS CURR 16TSSOP PDF资料下载
参数资料
| 型号： | LT3478EFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 18/24页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR HP CONS CURR 16TSSOP |
| 标准包装： | 95 |
| 恒定电流： | 是 |
| 拓扑： | PWM，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载，背光 |
| 类型 - 次要： | 颜色，白色 LED |
| 频率： | 200kHz ~ 2.25MHz |
| 电源电压： | 2.8 V ~ 36 V |
| 输出电压： | 42V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
LT3478/LT3478-1
APPLICATIO S I FOR ATIO
Local heating from the nearby inductor and Schottky diode
will also add to the ?nal junction temperature of the IC.
Based on empirical measurements, the effect of diode and
inductor heating on the LT3478-1 junction temperature
can be approximated as:
Δ T J (LT3478-1) = 5°C/W ? (P DIODE + P INDUCTOR )
P DIODE = (1 – D) ? V F ? I L(AVE)
1 – D = 0.316
V F = 0.5V
I L(AVE) = 2.41
P DIODE = 0.316 ? 0.5 ? 2.41 = 0.381W
P INDUCTOR = I L(AVE)2 ? DCR
DCR = inductor DC resistance (assume 0.05 Ω )
P INDUCTOR = (2.41) 2 ? 0.05 = 0.29W
The LT3478/LT3478-1 use a thermally enhanced FE pack-
age. With proper soldering to the Exposed Pad on the
underside of the package combined with a full copper plane
underneath the device, thermal resistance ( θ JA ) will be
about 35°C/W. For an ambient temperature of T A = 70°C,
the junction temperature of the LT3478-1 for the example
application described above, can be calculated as:
T J (LT3478-1)
= T A + θ JA (P TOT ) + 5(P DIODE + P INDUCTOR )
= 70 + 35(1.25) + 5(0.671)
= 70 + 44 + 4
= 118°C
In the above example, ef?ciency was initially assumed to
be η = 0.89. A lower ef?ciency ( η ) for the converter will
increase I L(AVE) and hence increase the calculated value
for T J . η can be calculated as:
η = P OUT /(P OUT + P LOSS )
If an application is built, the inductor current can be mea-
sured and a new value for junction temperature estimated.
Ideally a thermal measurement should be made to achieve
the greatest accuracy for T J .
Note: The junction temperature of the IC can be reduced
if a lower V IN supply is available – separate from the
inductor supply V S . In the above example, driving V IN
from an available 3V source (instead of V S = 8V) reduces
input quiescent losses in item(4) from 0.597W to 0.224W,
resulting in a reduction of T J from 118°C to 105°C.
Layout Considerations
As with all switching regulators, careful attention must be
given to PCB layout and component placement to achieve
optimal thermal,electrical and noise performance (Figure
12). The exposed pad of the LT3478/LT3478-1 (Pin 17)
is the only GND connection for the IC. The exposed pad
should be soldered to a continuous copper ground plane
underneath the device to reduce die temperature and
maximize the power capability of the IC. The ground path
for the R T resistor and V C capacitor should be taken from
nearby the analog ground connection to the exposed pad
(near Pin 9) separate from the power ground connection
to the exposed pad (near Pin 16). The bypass capacitor
for V IN should be placed as close as possible to the V IN
pin and the analog ground connection. SW pin voltage rise
and fall times are designed to be as short as possible for
maximum ef?ciency. To reduce the effects of both radiated
and conducted noise, the area of the SW trace should be
kept as small as possible. Use a ground plane under the
switching regulator to minimize interplane coupling. The
schottky diode and output capacitor should be placed as
close as possible to the SW node to minimize this high
frequency switching path. To minimize LED current sensing
errors for the LT3478, the terminals of the external sense
resistor R SENSE should be tracked to the V OUT and LED
pins separate from any high current paths.
P OUT = V OUT ? I LED = 17.15W
P LOSS (estimated) = P IC + P DIODE + P INDUCTOR = 1.92W
η = 17.15/(17.15 + 1.92) = 0.9
34781f
18
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B0F-CX-S | CONVERTER MOD DC/DC 72V 75W |
| VI-B0D-CX-S | CONVERTER MOD DC/DC 85V 75W |
| ML03512R1BAT2A | CAP MLO 2.1PF 50V 0603 |
| LT3599EUH#PBF | IC LED DRIVR WHITE BCKLGT 32-QFN |
| SWS1000L-5 | PWR SUP MED 5V 200A SGL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3478IFE | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A Monolithic LED Drivers with True Color PWM Dimming |
| LT3478IFE#PBF | 功能描述:IC LED DRVR HP CONS CURR 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| LT3478IFE#TRPBF | 功能描述:IC LED DRVR HP CONS CURR 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3478IFE-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A Monolithic LED Drivers with True Color PWM Dimming |
| LT3478IFE-1#PBF | 功能描述:IC LED DRVR HP CONS CURR 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
发布紧急采购，3分钟左右您将得到回复。