- 您现在的位置：买卖IC网 > PDF目录20772 > LT3478EFE#PBF (Linear Technology)IC LED DRVR HP CONS CURR 16TSSOP PDF资料下载
参数资料
| 型号： | LT3478EFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR HP CONS CURR 16TSSOP |
| 标准包装： | 95 |
| 恒定电流： | 是 |
| 拓扑： | PWM，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载，背光 |
| 类型 - 次要： | 颜色，白色 LED |
| 频率： | 200kHz ~ 2.25MHz |
| 电源电压： | 2.8 V ~ 36 V |
| 输出电压： | 42V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
LT3478/LT3478-1
PI FU CTIO S
SW (Pins 1, 2): Switch Pin. Collector of the internal NPN
power switch. Both pins are fused together inside the IC.
Connect the inductor and diode here and minimize the
metal trace area connected to this pin to minimize EMI.
V IN (Pin 3): Input Supply. Must be locally bypassed with
a capacitor to ground.
V S (Pin 4): Inductor Supply. Must be locally bypassed
with a capacitor to ground. Can be shorted to V IN if only
one supply is available (see L (Pin 5) function).
L (Pin 5): Inductor Pin. An internal resistor between V S
and L pins monitors inductor current to protect against
hysteresis allows programming of undervoltage lockout
(UVLO) hysteresis. ? S ? H ? D ? N above 1.4V turns the part on
and removes a 10μA sink current from the pin. ? S ? H ? D ? N = 0V
reduces V IN current < 3μA. S ? H ? D ? N ? can be directly connected
to V IN . If left open circuit the part will be turned off.
CTRL1 (Pin 12): CTRL1 pin voltage is used to program
maximum LED current (CTRL2 = V REF ). CTRL1 voltage
can be set by a resistor divider from V REF or an external
voltage source. Maximum LED current is given by:
(LT3478-1) Max LED Current = Min(CTRL1, 1.05) Amps
( LT 3478 ) Max LED Current =
inrush current. Exceeding 6A immediately turns off the
internal NPN power switch and discharges the soft-start
pin. Input current monitoring can be disabled by connect-
Min ( CTRL , 1 . 05 ) ?
0 . 1
R SE N SE
Amps
ing the inductor power supply directly to the L pin and
leaving the V S pin open (requires local bypass capacitor
to GND on L pin; not V S pin).
V OUT (Pin 6): Output voltage of the converter. Connect a
capacitor from this pin to ground. Internal circuitry moni-
tors V OUT for protection against open LED faults.
LED (Pin 7): Connect the LED string from this pin to
ground. An internal (LT3478-1)/external (LT3478) resistor
between the V OUT and LED pins senses LED current for
accurate control.
OVPSET (Pin 8): Programs V OUT overvoltage protection
level (OVP) to protect against open LED faults. OVP =
(OVPSET ? 41)V. OVPSET range is 0.3V to 1V for an OVP
range of typically 12.3V to 41V.
V C (Pin 9): Output of the transconductance error ampli?er
and compensation pin for the converter regulation loop.
V REF (Pin 10): Bandgap Voltage Reference. This pin can
supply up to 100μA. Can be used to program CTRL1,
CTRL2, OVPSET pin voltages using resistor dividers to
ground.
? S ? H ? D ? N (Pin 11): The S ? H ? D ? N ? pin has an accurate 1.4V
threshold and can be used to program an undervoltage
lockout (UVLO) threshold for system input supply using a
resistor divider from supply to ground. A 10μA pin current
(linear for 0.1V < CTRL1< 0.95V ; CTRL2 = V REF ) For maxi-
mum LED current, short CTRL1 and CTRL2 pins to V REF .
CTRL2 (Pin 13): The CTRL2 pin is available for program-
ming a decrease in LED current versus temperature
(setting temperature breakpoint and slope). This feature
allows the output LED(s) to be programmed for maximum
allowable current without damage at higher temperatures.
This maximizes LED usage and increases reliability. A
CTRL2 voltage with negative temperature coef?cient is
created using an external resistor divider from V REF with
temperature dependant resistance. If not used, CTRL2
should be tied to V REF .
PWM (Pin 14): Input pin for PWM dimming control. Above
1V allows converter switching and below 1V disables
switching with V C pin level maintained. With an external
MOSFET placed in series with the ground side of the LED
string, a PWM signal driving the PWM pin and MOSFET
gate provides accurate dimming control. The PWM signal
can be driven from 0V to 15V. If unused, the pin should
be connected to V REF .
R T (Pin 15): A resistor to ground programs switching
frequency between 200kHz and 2.25MHz.
SS (Pin 16): Soft-Start Pin. Placing a capacitor here pro-
grams soft-start timing to limit inductor inrush current
during start-up due to the converter. When inductor current
34781f
7
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B0F-CX-S | CONVERTER MOD DC/DC 72V 75W |
| VI-B0D-CX-S | CONVERTER MOD DC/DC 85V 75W |
| ML03512R1BAT2A | CAP MLO 2.1PF 50V 0603 |
| LT3599EUH#PBF | IC LED DRIVR WHITE BCKLGT 32-QFN |
| SWS1000L-5 | PWR SUP MED 5V 200A SGL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3478IFE | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A Monolithic LED Drivers with True Color PWM Dimming |
| LT3478IFE#PBF | 功能描述:IC LED DRVR HP CONS CURR 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| LT3478IFE#TRPBF | 功能描述:IC LED DRVR HP CONS CURR 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3478IFE-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4.5A Monolithic LED Drivers with True Color PWM Dimming |
| LT3478IFE-1#PBF | 功能描述:IC LED DRVR HP CONS CURR 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
发布紧急采购，3分钟左右您将得到回复。