参数资料
| 型号： | LT3493IDCB#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.2A 6DFN |
| 标准包装： | 500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.78 V ~ 34.2 V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 750kHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 6-DFN-EP（2x3） |
LT3493
APPLICATIONS INFORMATION
Now the required on-time has decreased below the
minimum on time of 120ns. Instead of the switch pulse
width becoming narrower to accommodate the lower duty
cycle requirement, the switch pulse width remains ?xed
at 120ns. In Figure 2 the inductor current ramps up to a
value exceeding the load current and the output ripple
increases to ~200mV. The part then remains off until the
output voltage dips below 100% of the programmed value
before it begins switching again.
Provided that the load can tolerate the increased output
voltage ripple and that the components have been properly
selected, operation above V IN(MAX) is safe and will not
damage the part. Figure 3 illustrates the switching wave-
forms when the input voltage is increased to its absolute
maximum rating of 40V.
As the input voltage increases, the inductor current ramps
up quicker, the number of skipped pulses increases and
the output voltage ripple increases. For operation above
V IN(MAX) the only component requirement is that the com-
ponents be adequately rated for operation at the intended
voltage levels.
The part is robust enough to survive prolonged operation
under these conditions as long as the peak inductor current
does not exceed 2.2A. Inductor current saturation may
further limit performance in this operating regime.
V SW
20V/DIV
I L
Inductor Selection and Maximum Output Current
A good ?rst choice for the inductor value is:
L = 1.6 (V OUT + V D )
where V D is the voltage drop of the catch diode (~0.4V) and
L is in μH. With this value there will be no subharmonic
oscillation for applications with 50% or greater duty cycle.
The inductor’s RMS current rating must be greater than
your maximum load current and its saturation current
should be about 30% higher. For robust operation in fault
conditions, the saturation current should be above 2.2A.
To keep ef?ciency high, the series resistance (DCR) should
be less than 0.1Ω. Table 1 lists several vendors and types
that are suitable.
Of course, such a simple design guide will not always
result in the optimum inductor for your application. A
larger value provides a higher maximum load current and
reduces output voltage ripple at the expense of slower
transient response. If your load is lower than 1.2A, then
you can decrease the value of the inductor and operate
with higher ripple current. This allows you to use a physi-
cally smaller inductor, or one with a lower DCR resulting in
higher ef?ciency. There are several graphs in the Typical
Performance Characteristics section of this data sheet that
show the maximum load current as a function of input
voltage and inductor value for several popular output volt-
ages. Low inductance may result in discontinuous mode
operation, which is okay, but further reduces maximum
load current. For details of the maximum output current
and discontinuous mode operation, see Linear Technology
Application Note 44.
0.5A/DIV
Catch Diode
V OUT
200mV/DIV
AC COUPLED
Depending on load current, a 1A to 2A Schottky diode is
recommended for the catch diode, D1. The diode must
C OUT = 10μF
V OUT = 3V
V IN = 40V
I LOAD = 0.75A
L = 10μH
2μs/DIV
Figure 3
3493 F03
have a reverse voltage rating equal to or greater than the
maximum input voltage. The ON Semiconductor MBRM140
is a good choice; it is rated for 1A continuous forward
current and a maximum reverse voltage of 40V.
3493fb
9
相关PDF资料 |
PDF描述 |
|---|---|
| LT3494EDDB#TRPBF | IC REG BOOST ADJ 0.18A 8DFN |
| LT3495EDDB-1#TRMPBF | IC REG BOOST ADJ 0.35A 10DFN |
| LT3501IFE#TRPBF | IC REG BUCK ADJ 3A DL 20TSSOP |
| LT3502IMS#TRPBF | IC REG BUCK ADJ 0.5A 10MSOP |
| LT3503EDCB#TRPBF | IC REG BUCK ADJ 1A 6DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3493IDCB-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.2A, 750kHz Step-Down Switching Regulator in 2mm × 3mm DFN |
| LT3494 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Low Noise Boost Converters with Output Disconnect |
| LT3494A | 制造商:LINER 制造商全称:Linear Technology 功能描述:20mA LED Driver and OLED Driver with Integrated Schottky in 3mm x 2mm DFN |
| LT3494AEDDB | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Low Noise Boost Converters with Output Disconnect |
| LT3494AEDDB#PBF | 制造商:Linear Technology 功能描述:BOOST 2.3 - 16V 0.35A 40V 制造商:Linear Technology 功能描述:BOOST, 2.3 - 16V, 0.35A, 40V, 20QFN |
发布紧急采购，3分钟左右您将得到回复。