- 您现在的位置：买卖IC网 > PDF目录20886 > LT3497EDDB#TRPBF (Linear Technology)IC LED DRIVR WHITE BCKLGT 10-DFN PDF资料下载
参数资料
| 型号： | LT3497EDDB#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT 10-DFN |
| 标准包装： | 2,500 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 2 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1.8MHz ~ 2.8MHz |
| 电源电压： | 2.5 V ~ 10 V |
| 输出电压： | 35V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN-EP（3x2） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
LT3497
APPLICATIONS INFORMATION
Table 4: R SENSE Value Selection for 200mV Sense
I LED (mA)
R SENSE ( Ω )
R1
LT3497
5
10
40
20
PWM
10kHz TYP
100k
C1
0.1 μ F
CTRL1,2
3497 F05
15
13.3
20
10
Figure 5. Dimming Control Using a Filtered PWM Signal
DIMMING CONTROL
There are three different types of dimming control circuits.
The LED current can be set by modulating the CTRL pin
with a DC voltage, a ?ltered PWM signal or directly with
a PWM signal.
Using a DC Voltage
For some applications, the preferred method of brightness
control is a variable DC voltage to adjust the LED current.
The CTRL pin voltage can be modulated to set the dim-
ming of the LED string. As the voltage on the CTRL pin
increases from 0V to 1.5V, the LED current increases from
0 to I LED . As the CTRL pin voltage increases beyond 1.5V,
it has no effect on the LED current.
The LED current can be set by:
Direct PWM Dimming
Changing the forward current ?owing in the LEDs not only
changes the intensity of the LEDs, it also changes the color.
The chromaticity of the LEDs changes with the change in
forward current. Many applications cannot tolerate any
shift in the color of the LEDs. Controlling the intensity of
the LEDs with a direct PWM signal allows dimming of the
LEDs without changing the color. In addition, direct PWM
dimming offers a wider dimming range to the user.
Dimming the LEDs via a PWM signal essentially involves
turning the LEDs on and off at the PWM frequency. The
typical human eye has a limit of ~60 frames per second.
By increasing the PWM frequency to ~80Hz or higher,
the eye will interpret that the pulsed light source is con-
tinuously on. Additionally, by modulating the duty cycle
(amount of “on time”) the intensity of the LEDs can be
when V CTRL > 1 . 5 V
when V CTRL < 1 . 25 V
I LED ≈
I LED ≈
200mV
R SENSE
V CTRL
6 . 25 ? R SENSE
controlled. The color of the LEDs remains unchanged in
this scheme since the LED current value is either zero or
a constant value.
Figure 6 shows a Li-ion powered 4/4 white LED driver. Direct
PWM dimming method requires an external NMOS tied
Feedback voltage variation versus control voltage is given
in the Typical Performance Characteristics.
Using a Filtered PWM Signal
A ?ltered PWM can be used to control the brightness of
the LED string. The PWM signal is ?ltered (Figure 5) by a
RC network and fed to the CTRL1, CTRL2 pins.
The corner frequency of R1, C1 should be much lower
than the frequency of the PWM signal. R1 needs to be
much smaller than the internal impedance in the CTRL
pins which is 10M Ω (typ).
between the cathode of the lowest LED in the string and
ground as shown in Figure 6. Si2318DS MOSFETs can be
used since its sources are connected to ground. The PWM
signal is applied to the (CTRL1 and CTRL2) control pins of
the LT3497 and the gate of the MOSFET. The PWM signal
should traverse between 0V to 5V to ensure proper turn
on and off of the converters and the NMOS transistors (Q1
and Q2). When the PWM signal goes high, LEDs are con-
nected to ground and a current of I LED = (200mV/R SENSE )
?ows through the LEDs. When the PWM signal goes low,
the LEDs are disconnected and turn off. The low PWM
input applied to the LT3497 ensures that the respective
3497f
11
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3217EUD#PBF | IC LED DRVR FLASH TORCH 16QFN |
| LTC3210EUD-1#PBF | IC LED DRIVR WHITE BCKLGT 16-QFN |
| P51-200-S-B-MD-4.5V-000-000 | SENSOR 200PSI 1/8-27NPT .5-4.5V |
| P51-1000-S-S-D-4.5V-000-000 | SENSOR 1000PSI 1/4-18NPT .5-4.5V |
| P51-1000-A-D-M12-4.5OVP-000-000 | SENSOR 1000PSI 7/16-20UNF 4.5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3498 | 制造商:LINER 制造商全称:Linear Technology 功能描述:20mA LED Driver and OLED Driver with Integrated Schottky in 3mm x 2mm DFN |
| LT3498EDDB | 制造商:LINER 制造商全称:Linear Technology 功能描述:20mA LED Driver and OLED Driver with Integrated Schottky in 3mm x 2mm DFN |
| LT3498EDDB#TRMPBF | 功能描述:IC LED DRVR WT/OLED BCKLGT 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3498EDDB#TRPBF | 功能描述:IC LED DRVR WT/OLED BCKLGT 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT34-SC | 制造商:THOMAS & BETTS 功能描述: |
发布紧急采购，3分钟左右您将得到回复。