- 您现在的位置：买卖IC网 > PDF目录20871 > LT3519IMS-1#TRPBF (Linear Technology)LED DRIVER WITH INTEGRATED SCHOT PDF资料下载
参数资料
| 型号： | LT3519IMS-1#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | LED DRIVER WITH INTEGRATED SCHOT |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 恒定电压： | 是 |
| 拓扑： | PWM，SEPIC，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载 |
| 频率： | 800kHz ~ 1.1MHz |
| 电源电压： | 3 V ~ 30 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 16-MSOP |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
LT3519/LT3519-1/LT3519-2
OPERATION
The LT3519/LT3519-1/LT3519-2 are constant frequency,
current mode regulators with an internal power switch and
Schottky. Operation can be best understood by referring
to the Block Diagram. At the start of each oscillator cycle,
the SR latch is set, which turns on the Q1 power switch.
A voltage proportional to the switch current is added to
a stabilizing ramp and the resulting sum is fed into the
positive terminal of the PWM comparator, A4. When this
voltage exceeds the level at the negative input of A4, the
SR latch is reset, turning off the power switch. The level
at the negative input of A4 is set by the error ampli?er A3.
A3 has two inputs, one from the voltage feedback loop and
the other one from the current loop. Whichever feedback
input is lower takes precedence to set the V C node voltage,
and forces the converter into either a constant-current or
a constant-voltage mode.
The LT3519/LT3519-1/LT3519-2 are designed to transi-
tion cleanly between these two modes of operation. The
current sense ampli?er senses the voltage across R SENSE
and provides an × 4 pre-gain to ampli?er A1. The output
of A1 is simply an ampli?ed version of the difference be-
tween the voltage across R SENSE and the lower of V CTRL
or 1.1V. In this manner, the error ampli?er sets the correct
peak switch current level to regulate the current through
R SENSE . If the error ampli?er’s output increases, more
current is delivered to the output; if it decreases, less
current is delivered. The current regulated in R SENSE can
be adjusted by changing the input voltage V CTRL . The FB
voltage loop is implemented by the ampli?er A2. When
the voltage loop dominates, the V C node voltage is set by
the ampli?ed difference of the internal reference of 1.22V
and the FB pin. If FB voltage is lower than the reference
voltage, the switch current will increase; if FB voltage is
higher than the reference voltage, the switch demand
current will decrease. The LED current sense feedback
interacts with the FB voltage feedback so that FB will not
exceed the internal reference and the voltage between ISP
and ISN will not exceed the threshold set by the CTRL pin.
For accurate current or voltage regulation, it is necessary
to be sure that under normal operating conditions the
appropriate loop is dominant. To deactivate the voltage
loop entirely, FB can be connected to GND. To deactivate
the LED current loop entirely, the ISP and ISN should be
tied together and the CTRL input tied to V REF .
When the FB input exceeds a voltage about 60mV lower
than the FB regulation voltage, the pull-down driver on
the OPENLED pin is activated. This function provides a
status indicator that the load may be disconnected and
the constant-voltage feedback loop is taking control of
the switching regulator.
Dimming of the LED array is accomplished by pulsing the
current using the PWM pin. When the PWM pin is low,
switching is disabled and the error ampli?er is turned off
so that it does not drive the V C node. Also, all internal loads
on the V C node are disabled so that the charge state of
the V C node will be saved on the internal compensation
capacitor. This feature reduces transient recovery time.
When the PWM input again transitions high, the demand
current for the switch returns to the value just before PWM
last transitioned low. To further reduce transient recovery
time, an external MOSFET should be used to disconnect
the LED array current loop when PWM is low, stopping
C OUT from discharging.
3519fa
8
相关PDF资料 |
PDF描述 |
|---|---|
| EBM10DRXS | CONN EDGECARD 20POS DIP .156 SLD |
| P51-500-S-J-MD-4.5V-000-000 | SENSOR 500PSI 3/8-24 UNF .5-4.5V |
| REC3-4812DRWZ/H6/C/SMD | CONV DC/DC 3W 18-72VIN +/-12VOUT |
| P51-300-A-M-M12-4.5OVP-000-000 | SENSOR 300PSI M10-1.0 6G .5-4.5V |
| P51-300-S-J-MD-4.5V-000-000 | SENSOR 300PSI 3/8-24 UNF .5-4.5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3519IMS-2#PBF | 功能描述:IC LED DVR W/SCHOTTKY DIO 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3519IMS-2#TRPBF | 功能描述:IC LED DVR W/DIO 2.2MHZ 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3519IMSPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:LED Driver with Integrated Schottky Diode |
| LT3519IMSTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:LED Driver with Integrated Schottky Diode |
| LT3524 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Regulating Pulse Width Modulator |
发布紧急采购，3分钟左右您将得到回复。