- 您现在的位置：买卖IC网 > PDF目录16303 > LT3650EMSE-8.4#PBF (Linear Technology)IC BATTERY CHARGER LI 12MSOP PDF资料下载
参数资料
| 型号： | LT3650EMSE-8.4#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/22页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY CHARGER LI 12MSOP |
| 标准包装： | 37 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 9 V ~ 32 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-TSSOP （0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 12-MSOP，裸露焊盘 |
| 包装： | 管件 |
| 产品目录页面： | 1340 (CN2011-ZH PDF) |
LT3650-8.2/LT3650-8.4
PIN FUNCTIONS
R SENSE =
charge current) is the desired soft-start interval (t SS ).
For no R RNG/SS , this capacitor value follows the relation:
C RNG/SS = 50μA ? t SS
The RNG/SS pin is pulled low during fault conditions,
allowing graceful recovery from faults should soft-start
functionality be implemented. Both the soft-start capaci-
tor and the programming resistor can be implemented in
parallel. All C/10 monitoring functions are disabled while
V RNG/SS is below 0.1V to accommodate long soft-start
intervals.
RNG/SS voltage can also be manipulated using an active
device, employing a pull-down transistor to disable charge
current or to dynamically servo maximum charge current.
Manipulation of the RNG/SS pin with active devices that
have low impedance pull-up capability is not allowed (see
the Applications Information section).
NTC (Pin 8): Battery Temperature Monitor Pin. This pin is
the input to the NTC (Negative Temperature Coefficient)
thermistor temperature monitoring circuit. This function is
enabled by connecting a 10kΩ, B = 3380 NTC thermistor
from the NTC pin to ground. The pin sources 50μA, and
monitors the voltage across the 10kΩ thermistor. When
the voltage on this pin is above 1.36V (T < 0°C) or below
0.29V (T > 40°C), charging is disabled and the CHRG and
FAULT pins are both pulled low. If internal timer termina-
tion is being used, the timer is paused, suspending the
charging cycle. Charging resumes when the voltage on
NTC returns to within the 0.29V to 1.36V active region.
There is approximately 5°C of temperature hysteresis
associated with each of the temperature thresholds. The
temperature monitoring function remains enabled while
thermistor resistance to ground is less than 250kΩ, so if
this function is not desired, leave the NTC pin unconnected.
BAT (Pin 9): Battery Voltage Monitor Pin. Connect 10μF
decoupling capacitance (C BAT ) from this pin to ground.
Depending on application requirements, larger value de-
coupling capacitors may be required (see the Application
Information section). The charge function operates to
achieve the final float voltage at this pin. The auto-restart
feature initiates a new charging cycle when the voltage at
the BAT pin falls 2.5% below this float voltage. Once the
charge cycle is terminated, the input bias current of the BAT
pin is reduced to <0.1μA, to minimize battery discharge
while the charger remains connected.
SENSE (Pin 10): Charge Current Sense Pin. Connect the
more positive voltage end of the inductor sense resistor
(R SENSE ) to the SENSE pin and the other end to the BAT
pin. The voltage across this resistor sets the average
charge current. The maximum average charge current
(I MAX ) corresponds to 100mV across the sense resistor.
This resistor can be set to program maximum charge
currents as high as 2A. The sense resistor value follows
the relation:
0.1V
I MAX
Once the charge cycle is terminated, the input bias cur-
rent of the SENSE pin is reduced to <0.1μA, to minimize
battery discharge while the charger remains connected.
BOOST (Pin 11): Bootstrapped Supply Rail for Switch
Drive. This pin facilitates saturation of the switch transistor.
Connect a 1μF or greater capacitor from the BOOST pin
to the SW pin. Operating range of this pin is 0V to 8.5V,
referenced to the SW pin. The voltage on the decoupling
capacitor is refreshed through a rectifying diode, with
the anode connected to either the battery output voltage
or an external source, and the cathode connected to the
BOOST pin.
SW (Pin 12): Switch Output Pin. This pin is the output
of the charger switch, and corresponds to the emitter of
the switch transistor. When enabled, the switch shorts
the SW pin to the V IN supply. The drive circuitry for this
switch is bootstrapped above the V IN supply using the
BOOST supply pin, allowing saturation of the switch for
maximum efficiency. The effective on-resistance of the
boosted switch is 0.175Ω.
SGND (Pin 13): Ground Reference and Backside Exposed
Lead Frame Thermal Connection. Solder the exposed lead
frame to the PCB ground plane.
36508284fd
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4070EDDB#TRMPBF | IC LI-ION/POLY BATT CHARGER 8DFN |
| LTC4071EMS8E#PBF | IC LI-ION/POLY BATT CHRGR 8-MSOP |
| 3-1906012-9 | CA 2.0MM OFNR 50/125,LC SEC RED |
| 3-1906014-9 | CA 2.0MM OFNR 50/125,LC SEC YEL |
| 3-1906054-9 | CA 2MM OFNR 62.5/125,LC SEC GRE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3650IDD-4.1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage 2 Amp Monolithic Li-Ion Battery Charger |
| LT3650IDD-4.1#PBF | 功能描述:IC CHARGER LI-ION 2A 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LT3650IDD-4.1#TRPBF | 功能描述:IC CHARGER LI-ION 4.1V 2A 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT3650IDD-4.1PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage 2 Amp Monolithic Li-Ion Battery Charger |
| LT3650IDD-4.1TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage 2 Amp Monolithic Li-Ion Battery Charger |
发布紧急采购，3分钟左右您将得到回复。