- 您现在的位置：买卖IC网 > PDF目录80197 > LT3651EUHE-4.2#PBF (LINEAR TECHNOLOGY CORP) BATTERY CHARGE CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PQCC36 PDF资料下载
参数资料
| 型号： | LT3651EUHE-4.2#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | BATTERY CHARGE CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PQCC36 |
| 封装： | 5 X 6 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-36 |
| 文件页数： | 21/22页 |
| 文件大小： | 213K |
| 代理商： | LT3651EUHE-4.2#PBF |
LT3651-4.1/LT3651-4.2
8
365142fb
PIN FUNCTIONS
CHRG (Pin 26): Open-Collector Charger Status Output.
This pin indicates the battery charging status. Typically
a resistor pull-up is used on this pin. This status pin can
be pulled up to voltages as high as VIN when disabled,
and can sink currents up to 10mA when enabled. CHRG
is pulled low during a battery charging cycle. When the
charge cycle is terminated, the CHRG pin becomes high
impedance. If the internal timer is used for termination,
the pin stays low during the charging cycle until the charge
current drops below a C/10 rate, or approximately 10%
of the maximum charge current. A temperature fault also
causes this pin to be pulled low.
SHDN (Pin 27): Shutdown Pin. This pin can be used for
precision UVLO functions. When this pin rises above the
1.20V threshold, the part is enabled. The pin has 95mV of
voltage hysteresis. When in shutdown mode, all charging
functions are disabled. When the SHDN pin is pulled below
0.4V, the IC enters a low current shutdown mode where
the VIN pin current is reduced to 17μA. Typical SHDN pin
input bias current is 10nA. Connect the pin to VIN if the
shutdown function is not desired.
ILIM (Pin 28): Input Current Limit Programming This pin
allows for setting and dynamic adjustment of the system
input current limit, and can be used to employ a soft-start
function. The voltage on this pin sets the maximum input
current by setting the maximum voltage across the input
current sense resistor, placed between CLP and CLN.
The effective range on the pin is 0V to 1V. 50μA is sourced
from this pin usually to a resistor (RILIM) to ground. VIILIM
represents approximately 11 times the maximum voltage
across the input current sense resistor. If no RILIM is used
the part will default to maximum input current.
Soft-start functionality for input current can be imple-
mented with a capacitor (CILIM) from ILIM to ground. The
soft-start capacitor and the programming resistor can be
implemented in parallel.
CLP/CLN (Pin 29/Pin 30): System Current Limit Positive
and Negative Input. System current levels are monitored
by connecting a sense resistor from the input power sup-
ply to the CLP pin, connecting a sense resistor from the
CLP pin to the CLN pin and then connecting CLN to VIN.
The system load is then delivered from the CLN pin. The
LT3651 servos the maximum charge current required to
maintain programmed maximum system current. The
system current limit is set as a function of the voltage
on the ILIM pin and the input current sense resistor. This
function is disabled by shorting CLP, CLN and VIN together.
VIN (Pins 32, 33, 34): Charger Input Supply. These pins
provide power for the LT3651. Charge current for the
battery flows into this pin. IVIN is less than 100μA after
charge termination. Connect both pins together.
RNG/SS (Pin 35): Charge Current Range and Soft-Start
Pin. This pin allows for setting and dynamic adjustment
of the maximum charge current, and can be used to em-
ploy a soft-start function. The voltage on this pin sets the
maximum charge current by setting the maximum voltage
across the charge current sense resistor, RSENSE, placed
between SENSE and BAT.
The effective range on the pin is 0V to 1V. 50μA is sourced
from this pin usually to a resistor (RRNG/SS) to ground.
VRNG/SS represents approximately 10 times the maximum
voltage across the charge current sense resistor. If no RRNG/
SS is used the part will default to maximum charge current.
Soft-start functionality for charge current can be imple-
mented by connecting a capacitor (CRNG/SS) from RNG/SS
to ground. The soft-start capacitor and the programming
resistor can be implemented in parallel. The RNG/SS pin
is pulled low during fault conditions, allowing graceful
recovery from faults if CRNG/SS is used.
RT (Pin 36): Switcher Oscillator Timer Set Pin. A resis-
tor from this pin to ground sets the switcher oscillator
frequency. Typically this is 54.9k for fOSC = 1MHz.
相关PDF资料 |
PDF描述 |
|---|---|
| LMX2515LQ0701/NOPB | PLL FREQUENCY SYNTHESIZER, 26 MHz, QCC28 |
| LM3544M-H/NOPB | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LMD12D | 2-OUTPUT 75 W DC-DC REG PWR SUPPLY MODULE |
| LMD100S | 1-OUTPUT 75 W DC-DC REG PWR SUPPLY MODULE |
| LK1001-7D3T | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3651EUHE-8.2#PBF | 制造商:Linear Technology 功能描述:IC CHRG MGMT LI-ION/LI-POL 36QFN 制造商:Linear Technology 功能描述:DP-Battery Charger, Monolithic 4A High Voltage Li-Ion Battery Charger |
| LT3651EUHE-8.2#TRPBF | 制造商:Linear Technology 功能描述:IC CHRG MGMT LI-ION/LI-POL 36QFN 制造商:Linear Technology 功能描述:DP-Battery Charger, Monolithic 4A High Voltage Li-Ion Battery Charger |
| LT3651EUHE-8.4#PBF | 制造商:Linear Technology 功能描述:IC CHRG MGMT LI-ION/LI-POL 36QFN 制造商:Linear Technology 功能描述:DP-Battery Charger, Monolithic 4A High Voltage Li-Ion Battery Charger |
| LT3651EUHE-8.4#TRPBF | 制造商:Linear Technology 功能描述:IC CHRG MGMT LI-ION/LI-POL 36QFN 制造商:Linear Technology 功能描述:DP-Battery Charger, Monolithic 4A High Voltage Li-Ion Battery Charger |
| LT3651IUHE-4.1#PBF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion/Li-Pol 4000mA 4.1V 36-Pin QFN EP 制造商:Linear Technology 功能描述:IC CHRG MGMT LI-ION/LI-POL 36QFN 制造商:Linear Technology 功能描述:DP-Battery Charger, Monolithic 4A High Voltage Li-Ion Battery Charger |
发布紧急采购，3分钟左右您将得到回复。