- 您现在的位置：买卖IC网 > PDF目录80141 > LT3652HVIMSE#PBF (LINEAR TECHNOLOGY CORP) BATTERY CHARGE CONTROLLER, PDSO12 PDF资料下载
参数资料
| 型号： | LT3652HVIMSE#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | BATTERY CHARGE CONTROLLER, PDSO12 |
| 封装： | LEAD FREE, PLASTIC, MSOP-12 |
| 文件页数： | 5/24页 |
| 文件大小： | 250K |
| 代理商： | LT3652HVIMSE#PBF |
LT3652HV
13
3652hvf
APPLICATIONS INFORMATION
In low VIN applications, the BOOST supply can be powered
by an external source for start-up, eliminating the VIN
start-up requirement.
VBAT Output Decoupling
An LT3652HV charger output requires bypass capacitance
connected from the BAT pin to ground (CBAT). A 10μF
ceramic capacitor is required for all applications. In systems
where the battery can be disconnected from the charger
output, additional bypass capacitance may be desired for
visual indication for a no-battery condition (see the Status
Pins section).
If it is desired to operate a system load from the LT3652HV
charger output when the battery is disconnected, additional
bypass capacitance is required. In this type of application,
excessive ripple and/or low amplitude oscillations can oc-
cur without additional output bulk capacitance. For these
applications, place a 100μF low ESR non-ceramic capacitor
(chip tantalum or organic semiconductor capacitors such
as Sanyo OS-CONs or POSCAPs) from BAT to ground,
in parallel with the 10μF ceramic bypass capacitor. This
additional bypass capacitance may also be required in
systems where the battery is connected to the charger
with long wires. The voltage rating of CBAT must meet or
exceed the battery float voltage.
Inductor Selection
The primary criterion for inductor value selection in an
LT3652HV charger is the ripple current created in that
inductor. Once the inductance value is determined, an
inductor must also have a saturation current equal to or
exceeding the maximum peak current in the inductor. An
inductor value (L), given the desired amount of ripple cur-
rent (ΔIMAX) can be approximated using the relation:
L = (10 RSENSE / ΔIMAX) VBAT(FLT)
[1 – (VBAT(FLT) / VIN(MAX))]
(μH)
In the above relation, ΔIMAX is the normalized ripple cur-
rent, VIN(MAX) is the maximum operational voltage, and
VF is the forward voltage of the rectifying Schottky diode.
Ripple current is typically set within a range of 25% to
35% of ICHG(MAX), so an inductor value can be determined
by setting 0.25 < ΔIMAX < 0.35.
Figure 3. 14.4V at 1.5A Switched Inductor Values
MAXIMUM OPERATIONAL VIN VOLTAGE (V)
18
20
22
4
SWITCHED
INDUCTOR
V
ALUE
(μH)
12
10
14
24
16
18
20
22
34
3652 F03
8
6
26
28
24
30
32
Magnetics vendors typically specify inductors with
maximum RMS and saturation current ratings. Select an
inductor that has a saturation current rating at or above (1+
ΔIMAX/2) ICHG(MAX), and an RMS rating above ICHG(MAX).
Inductors must also meet a maximum volt-second product
requirement. If this specification is not in the data sheet of
an inductor, consult the vendor to make sure the maximum
volt-second product is not being exceeded by your design.
The minimum required volt-second product is:
VBAT(FLT) (1 – VBAT(FLT)/VIN(MAX)) (V μS)
Rectifier Selection
The rectifier diode from SW to GND, in a LT3652HV battery
charger provides a current path for the inductor current
when the main power switch is disabled. The rectifier is
selected based upon forward voltage, reverse voltage, and
maximum current. A Schottky diode is required, as low
forward voltage yields the lowest power loss and highest
efficiency. The rectifier diode must be rated to withstand
reverse voltages greater than the maximum VIN voltage.
相关PDF资料 |
PDF描述 |
|---|---|
| LME0509SC | DC-DC REG PWR SUPPLY MODULE |
| LSN-1.5/10-D5B-C | DC-DC REG PWR SUPPLY MODULE |
| LSN-1.5/10-D5BH | DC-DC REG PWR SUPPLY MODULE |
| LSN-2.5/10-D5B-C | DC-DC REG PWR SUPPLY MODULE |
| LM2577MX-ADJ/NOPB | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3652HVIMSE-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power Tracking 2A Battery Charger |
| LT3652IDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power Tracking 2A Battery Charger for Solar Power |
| LT3652IDD#PBF | 功能描述:IC BATTERY CHARGER 2A 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT3652IDD#TRPBF | 功能描述:IC BATTERY CHARGER 2A 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT3652IDDPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power Tracking 2A Battery Charger for Solar Power |
发布紧急采购，3分钟左右您将得到回复。