参数资料
| 型号： | LT3653IDCB#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.2A 8DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 4.8 V ~ 6 V |
| 输入电压： | 7.5 V ~ 30 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.5MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-DFN（3x2） |
LT3653
APPLICATIONS INFORMATION
Inductor Selection
A 4.7μH inductor is recommended for most LT3653 ap-
plications. This value provides a good tradeoff between
size and ripple current. The inductor’s RMS current rating
must be greater than the maximum load current and its
saturation current should be about 30% higher. The output
current limit circuit tightly controls the maximum average
inductor current therefore the inductor RMS current rating
does not have to be overrated to handle short-circuit or
overload conditions. For high ef?ciency, keep the series
resistance (DCR) less than 0.1Ω. Output voltage ripple
can be reduced by using a higher value inductor. The cost
is a larger physical size and poorer transient response.
A lower value inductor has higher ripple currents but is
physically smaller or, for the same size, has lower DCR
usually resulting in higher ef?ciency.
The input capacitor is required to reduce the resulting volt-
age ripple at the LT3653 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
Place the capacitor in close proximity to the LT3653 and
the catch diode (see the PCB Layout section).
Output Capacitor
A 10μF or greater ceramic capacitor is required for low
output ripple and good transient response. Ceramic ca-
pacitors have very low equivalent series resistance (ESR)
and provide the best ripple performance. Use X5R or X7R
types and keep in mind that a ceramic capacitor biased
with V OUT has less than its nominal capacitance.
High performance electrolytic capacitors can be used for
the output capacitor. Low ESR is important, so choose
one that is intended for use in switching regulators. Keep
the ESR less than 0.1Ω.
Catch Diode
The catch diode conducts current only during switch off
time. Average forward current in normal operation is
calculated from:
I LIM Resistor
The LT3653 output current limit controls the maximum
current delivered from the LT3653 regulator. This allows
I D ( AVG ) = I OUT
V IN ? V OUT
V IN
tighter control of the system power dissipation and also
protects the inductor and diode from overheating during
an overload or short-circuit condition. A resistor connected
where I OUT is the maximum output load current pro-
grammed by the I LIM resistor. Peak reverse voltage is
equal to the regulator input voltage. Use a Schottky diode
with a reverse voltage rating greater than the maximum
input voltage. The overvoltage protection feature in the
LT3653 keeps the switch off when V IN > 33V (typical),
allowing the use of a 40V rated Schottky, even when V IN
ranges up to 60V.
from the I LIM pin to GND programs the output current
limit. Table 1 details the I LIM resistor values for speci?c
desired output current limits
Table 1. Output Current Limit vs R ILIM Value
OUTPUT CURRENT LIMIT (A) R ILIM VALUE (kΩ)
0.4 121
0.6 66.5
0.8 45.3
1 33.2
Input Capacitor
Bypass the input of the LT3653 circuit with a 4.7μF or higher
1.2
27.4
C BOOST =
valueceramiccapacitorofX7RorX5Rtype.Y5Vtypeshave
poor performance over temperature and applied voltage and
should not be used. If the input power source has high im-
pedance, or there is signi?cant inductance due to long wires
or cables, additional bulk capacitance may be necessary.
This can be provided with a low performance electrolytic
capacitor. Step-down regulators draw current from the
input supply in pulses with very fast rise and fall times.
Boost Capacitor Selection
The boost capacitor is calculated with the following for-
mula:
( I OUT ( MAX ) ) ? V OUT
0 . 1 V ? 30 ? V IN ? 1 . 5 MHz
Typically, a 0.1μF capacitor is used.
3653f
8
相关PDF资料 |
PDF描述 |
|---|---|
| LT3663HMS8E-3.3#PBF | IC REG BUCK 3.3V 1.2A 8MSOP |
| LT3680HMSE#TRPBF | IC REG BUCK ADJ 3.5A 10MSOP |
| LT3681EDE#TRPBF | IC REG BUCK ADJ 2A 14DFN |
| LT3682IDD#TRPBF | IC REG BUCK ADJ 1A 12DFN |
| LT3684IMSE#TRPBF | IC REG BUCK ADJ 2A 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3663EDCB#TRMPBF | 功能描述:IC REG BUCK ADJ 1.2A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3663EDCB#TRPBF | 功能描述:IC REG BUCK ADJ 1.2A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3663EMS8E#PBF | 功能描述:IC REG BUCK ADJ 1.2A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3663EMS8E#PBF | 制造商:Linear Technology 功能描述:IC STEP-DOWN REGULATOR MSOP-8 |
| LT3663EMS8E#TRPBF | 功能描述:IC REG BUCK ADJ 1.2A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。