参数资料
| 型号： | LT3653IDCB#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.2A 8DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 4.8 V ~ 6 V |
| 输入电压： | 7.5 V ~ 30 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.5MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-DFN（3x2） |
LT3653
APPLICATIONS INFORMATION
Battery Charger Operation
Connect the control node, V C pin, of the LT3653 to the
V C pin of the battery charger power path controller. The
V C node is internally clamped; however, take care not to
overdrive the pin. The LT3653 is internally compensated
with a pole zero combination on the output of the g m
ampli?er, G1. Check stability over the full input voltage
range, output load range and temperature.
Connect the HVOK node of the LT3653 to the high voltage
present pin of the charger. This is the WALL pin on the
LTC4098. The HVOK pin is capable of supplying up to 1mA
of drive current. When the HVOK pin is low the LT3653 is
not switching and the system output cannot be supported
by the LT3653 regulator. See the Typical Applications sec-
tion for different con?gurations.
PCB Layout
Proper operation and minimum EMI requires a careful
printed circuit board layout. Figure 1 shows the recom-
mended component placement with trace, ground plane
and via locations. Note that large, switched currents ?ow
in the LT3653’s V IN and SW pins, the catch diode (D1)
and the input capacitor (C1). Keep the loop formed by
these components as small as possible and tied to system
ground in only one place. Place these components, along
with the inductor and output capacitor, on the same side
of the circuit board, with their connections made on that
layer. Place a local, unbroken ground plane below these
components, and tie this ground plane to system ground
at one location, ideally at the ground terminal of the output
capacitor C2. Make the SW and BOOST nodes as short
as possible. Include vias near the exposed GND pad of
the LT3653 to help remove heat from the LT3653 to the
ground plane.
High Temperature Considerations
The die temperature of the LT3653 must not exceed
the maximum rating of 125°C. This is generally not a
concern unless the ambient temperature is above 85°C.
For higher temperatures, take care in the layout of the
circuit to ensure good heat sinking of the LT3653. Derate
the maximum load current as the ambient temperature
approaches 125°C. The die temperature is calculated by
multiplying the LT3653 power dissipation by the thermal
resistance from junction to ambient. Power dissipation
within the LT3653 is estimated by calculating the total
power loss from an ef?ciency measurement and subtracting
the catch diode loss. Thermal resistance depends on the
layout of the circuit board, but 64°C/W is typical for the
(2mm × 3mm) DFN (DCB) package.
Other Linear Technology Publications
Application Notes 19, 35 and 44 contain more detailed
descriptions and design information for Buck regulators
and other switching regulators. The LT1376 data sheet
has a more extensive discussion of output ripple, loop
compensation and stability testing.
V IN
C1
GND
TO CHARGER:
HVOK
V C
1
2
3
4
8
7
6
5
C3
C2
R ILIM
V OUT
3653 F01
Figure 1. LT3653 PCB Layout
3653f
9
相关PDF资料 |
PDF描述 |
|---|---|
| LT3663HMS8E-3.3#PBF | IC REG BUCK 3.3V 1.2A 8MSOP |
| LT3680HMSE#TRPBF | IC REG BUCK ADJ 3.5A 10MSOP |
| LT3681EDE#TRPBF | IC REG BUCK ADJ 2A 14DFN |
| LT3682IDD#TRPBF | IC REG BUCK ADJ 1A 12DFN |
| LT3684IMSE#TRPBF | IC REG BUCK ADJ 2A 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3663EDCB#TRMPBF | 功能描述:IC REG BUCK ADJ 1.2A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3663EDCB#TRPBF | 功能描述:IC REG BUCK ADJ 1.2A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3663EMS8E#PBF | 功能描述:IC REG BUCK ADJ 1.2A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3663EMS8E#PBF | 制造商:Linear Technology 功能描述:IC STEP-DOWN REGULATOR MSOP-8 |
| LT3663EMS8E#TRPBF | 功能描述:IC REG BUCK ADJ 1.2A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。