- 您现在的位置：买卖IC网 > PDF目录1825 > LT3690MPUFE#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 4A 26QFN PDF资料下载
参数资料
| 型号： | LT3690MPUFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/30页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 4A 26QFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 20 V |
| 输入电压： | 3.9 V ~ 36 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 138kHz ~ 1.5MHz |
| 电流 - 输出： | 4A |
| 同步整流器： | 是 |
| 工作温度： | -55°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 26-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 26-QFN-EP（4x6） |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LT3690
PIN FUNCTIONS
SW (Pins 1-4, 23-26, Exposed Pad Pin 27): The SW pin
is the emitter output of the internal highside NPN power
switch (HS) and the drain output of the internal lowside
power N-channel switch (LS). Connect this pin to the
inductor and boost capacitor. This pin is driven up to the
V IN voltage by the HS switch during the on-time of the
PWM duty cycle. The inductor current drives the SW pin
negative during the off-time. The on-resistance of the LS
switch and the internal Schottky diode fixes the negative
voltage.
The exposed pad is connected internally with SW pins
1-4, 23-26 and should be soldered to a large copper area
to reduce thermal resistance.
SYNC (Pin 5): The SYNC pin is used to synchronize the
internal oscillator to an external signal. It is directly logic
compatible and can be driven with any signal between
20% and 80% duty cycle. The synchronizing range is
from 170kHz to 1.5MHz. See the Synchronization section
in the Applications Information section for details. When
not used for synchronization, the SYNC pin can be tied
to ground to select low ripple Burst Mode operation or
tied to the output voltage to select standard PWM mode.
RT (Pin 7): Oscillator Resistor Input. Connecting a resis-
tor to ground (Pin 10) from this pin sets the switching
frequency.
V C (Pin 8): The V C pin is the output of the internal error
amplifier. The voltage on this pin controls the peak switch
current. Tie an RC network from this pin to ground to
compensate the control loop.
FB (Pin 9): The LT3690 regulates the FB pin to 0.8V.
Connect the feedback resistor divider tap to this pin. The
adjacent ground pin (Pin 10) is recommended for the
resistor divider.
SS (Pin 11): The SS pin is used to provide a soft-start
or tracking function. The internal 2μA pull-up current
I SS in combination with an external capacitor tied to this
pin creates a voltage ramp. The output voltage tracks to
this voltage. For tracking, tie a resistor divider to this pin
from the tracked output. In undervoltage, overvoltage
and thermal shutdown, the SS pin pulls low if the output
voltage is below the power good threshold to restart the
output voltage with soft-start behavior. Leave this pin
disconnected if unused.
UVLO (Pin 12): Tie a resistor divider between V IN , UVLO,
and GND to program an undervoltage lockout threshold.
The UVLO pin has an accurate 1.25V threshold. Above the
threshold, the part operates normally. Below the threshold,
the part drops into a low quiescent current state. See the
Undervoltage Lockout section in the Applications Informa-
tion section for more details.
V IN (Pins 13, 14, 15): The V IN pin supplies current to
the LT3690’s internal regulator and to the internal power
switch. This pin must be locally bypassed.
EN (Pin 17): The EN input is used to put the LT3690 in
shutdown mode. Pull to GND to shut down the LT3690.
Tie to 1.5V or more for normal operation.
PG (Pin 18): The PG pin is the open collector output of
an internal comparator. PG remains low until the FB pin is
within 10% of the final regulation voltage. The PG output
is valid when V IN is above 3.9V and EN is high.
BIAS (Pin 19): This pin connects to the anode of the internal
boost Schottky diode. BIAS also supplies the current to
the LT3690’s internal regulator. Tie this pin to the lowest
available voltage source above 3V (typically V OUT ). This
pin must be locally bypassed with 10nF.
V CCINT (Pin 20): V CCINT is an output of the internally gen-
erated supply voltage for the synchronous power DMOS
transistor driver. An external capacitor C VCC must be con-
nected between this pin and ground (Pin 21) to buffer the
internal supply voltage of the LS switch.
BST (Pin 22): This pin is used to provide, with the external
boost capacitor, a drive voltage higher than the input volt-
age V IN to the internal bipolar NPN power switch.
GND (Exposed Pad Pin 28, Pin 6, Pin 10, Pin 16, Pin 21):
Ground. The exposed pad is connected internally to GND
Pins 6, 10, 16 and 21, and should be soldered to a large
copper area to reduce thermal resistance.
3690fa
9
相关PDF资料 |
PDF描述 |
|---|---|
| LT3692IUH#TRPBF | IC REG BUCK ADJ 3.5A DL 32QFN |
| LT3693IMSE#TRPBF | IC REG BUCK ADJ 3.5A 10MSOP |
| LT3695HMSE-5#TRPBF | IC REG BUCK 5V 1A 16MSOP |
| LT3710EFE#TRPBF | IC REG CTRLR BUCK PWM 16-TSSOP |
| LT3724EFE#PBF | IC REG CTRLR BST INV PWM 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3692 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Dual Tracking |
| LT3692A | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Dual Tracking |
| LT3692AEFE#PBF | 功能描述:IC REG BUCK ADJ 3.5A DL 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3692AEFE#TRPBF | 功能描述:IC REG BUCK ADJ 3.5A DL 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3692AEUH#PBF | 功能描述:IC REG BUCK ADJ 3.5A DL 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。