- 您现在的位置：买卖IC网 > PDF目录30767 > LT3694IUFD#PBF (LINEAR TECHNOLOGY CORP) 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 PDF资料下载
参数资料
| 型号： | LT3694IUFD#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
| 封装： | 4 X 5 MM, LEAD FREE, PLASTIC, MO-220, QFN-28 |
| 文件页数： | 4/28页 |
| 文件大小： | 276K |
| 代理商： | LT3694IUFD#PBF |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3694/LT3694-1
12
36941fa
APPLICATIONS INFORMATION
where f is the switching frequency of the LT3694 and L
is the value of the inductor. The peak inductor and switch
current is:
I
SWPK = ILPK = IOUT +
ΔI
L
2
To maintain output regulation, this peak current must be
less than the LT3694’s switch current limit, ILIM. ILIM is at
least 3.5A at low duty cycles (0.1) and decreases linearly
to 2.8A at DC = 0.8.
The minimum inductance can now be calculated as:
L
MIN =
1
DC
MIN
2 f
V
OUT + VF
I
LIM IOUT
However, it’s generally better to use an inductor larger
than the minimum value. The minimum inductor has large
ripple currents which increase core losses and require
large output capacitors to keep output voltage ripple low.
Select an inductor greater than LMIN that keeps the ripple
current below 30% of ILIM.
For input voltages greater than 30V, use an inductor with
a saturation current of 6A or greater and an inductance
value of 3.3μH or greater.
The inductor’s RMS current rating must be greater than the
maximum load current and its saturation current should
be greater than ILPK. For highest efficiency, the series
resistance (DCR) should be less than 0.1Ω. Table 2 lists
several vendors and types that are suitable.
Table 2. Inductors
SERIES
INDUCTANCE
RANGE (μH)
CURRENT
RANGE (A)
MANUFACTURER
WE-HC
1 to 6.5
6 to 15
Würth Elektronik
www.we-online.com
MSS1048
0.8 to 8
4 to 8
Coilcraft
www.coilcraft.com
CDRH103R
0.8 to 10
2.8 to 8.3
Sumida
www.sumida.com
VLF
2.2 to 10
3.8 to 7.7
TDK
www.component.tdk.
com
IHLP-2525CZ-11
1 to 10
2.5 to 9.5
Vishay
www.vishay.com
This analysis is valid for continuous mode operation
(IOUT > ILIM/2). For details of maximum output current in
discontinuous mode operation, see the Linear Technol-
ogy Application Note 44. Finally, for duty cycles greater
than 50% (VOUT/VIN > 0.5), a minimum inductance is
required to avoid subharmonic oscillations. This minimum
inductance is:
L
MIN =
(V
OUT + VF )
2A f
SW
with LMIN in μH and fSW in MHz. A detailed discussion
of subharmonic oscillations can be found in the Linear
Technology Application Note 19.
Input Capacitor Selection
Bypass the input of the LT3694 circuit with a ceramic
capacitor of X7R or X5R type. Y5V types have poor
performance over temperature and applied voltage, and
should not be used. A 4.7μF to 22μF ceramic capacitor
is adequate to bypass the LT3694 and will easily handle
the ripple current. Use a 22μF capacitor with fSW between
250kHz and 800kHz. Use a 10μF capacitor with fSW be-
tween 800kHz and 1.6MHz. Use a 4.7μF capacitor above
1.6MHz. Always check for sufficient margin by reducing
the capacitor value until the dropout increases by >500mV.
If the input power source has high impedance, or there
is significant inductance due to long wires or cables,
additional bulk capacitance may be necessary. This
can be provided with a lower performance electrolytic
capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT3694 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 10μF capacitor is capable of this task, but only if it is
placed close to the LT3694 and the catch diode (see the
PCB Layout section). A second precaution regarding the
ceramic input capacitor concerns the maximum input
voltage rating of the LT3694. A ceramic input capacitor
combined with trace or cable inductance forms a high
相关PDF资料 |
PDF描述 |
|---|---|
| LT3694-1IFE#PBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3694-1EFE#PBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3695IMSE-5#PBF | 2 A SWITCHING REGULATOR, 2420 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3695EMSE-5#TRPBF | 2 A SWITCHING REGULATOR, 2420 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3695IMSE-5#TRPBF | 2 A SWITCHING REGULATOR, 2420 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3695 | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A Fault Tolerant Micropower Step-Down Regulator |
| LT3695EMSE#PBF | 功能描述:IC REG BUCK ADJ 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3695EMSE#TRPBF | 功能描述:IC REG BUCK ADJ 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3695EMSE-3.3#PBF | 功能描述:IC REG BUCK 3.3V 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3695EMSE-3.3#PBF | 制造商:Linear Technology 功能描述:IC STEP-DOWN REGULATOR MSOP-16 |
发布紧急采购，3分钟左右您将得到回复。