- 您现在的位置：买卖IC网 > PDF目录13913 > LT3695HMSE#PBF (Linear Technology)IC REG BUCK ADJ 1A 16MSOP PDF资料下载
参数资料
| 型号： | LT3695HMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/30页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1A 16MSOP |
| 标准包装： | 37 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 20 V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 250kHz ~ 2.2MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LT3695 Series
APPLICATIONS INFORMATION
Audible Noise
Ceramic capacitors are small, robust and have very low
ESR. However, ceramic capacitors can sometimes cause
problems when used with the LT3695 regulators due to
their piezoelectric nature. When in Burst Mode operation,
the LT3695 regulators’ switching frequency depends on the
load current, and at very light loads the LT3695 regulators
can excite the ceramic capacitor at audio frequencies, gen-
erating audible noise. Since the LT3695 regulators operate
at a lower current limit during Burst Mode operation, the
noise is typically very quiet. If this is unacceptable, use
a high performance tantalum or electrolytic capacitor at
the output.
Frequency Compensation
The LT3695 regulators use current mode control to
regulate the output. This simpli?es loop compensation.
In particular, the LT3695 regulators do not require the
ESR of the output capacitor for stability, so you are free
to use ceramic capacitors to achieve low output ripple and
small circuit size. Frequency compensation is provided by
the components tied to the V C pin, as shown in Figure 1.
Generally a capacitor (C C ) and a resistor (R C ) in series to
ground are used. In addition, there may be a lower value
capacitor in parallel. This capacitor (C F ) is used to ?lter
noise at the switching frequency, and is required only if a
phase-lead capacitor (C PL , LT3695 only) is used or if the
output capacitor has high ESR.
LT3695
Loop compensation determines the stability and transient
performance. Optimizing the design of the compensation
network depends on the application and type of output
capacitor. A practical approach is to start with one of the
circuits in this data sheet that is similar to your applica-
tion and tune the compensation network to optimize the
performance. Stability should then be checked across all
operating conditions, including load current, input voltage
and temperature. The LT1375 data sheet contains a more
thorough discussion of loop compensation and describes
how to test the stability using a transient load. Figure 1
shows an equivalent circuit for the LT3695 regulators
control loop. The error ampli?er is a transconductance
ampli?er with ?nite output impedance. The power section,
consisting of the modulator, power switch and inductor, is
modeled as a transconductance ampli?er generating an
output current proportional to the voltage at the V C pin.
Note that the output capacitor integrates this current, and
that the capacitor on the V C pin (C C ) integrates the error
ampli?er output current, resulting in two poles in the loop.
In most cases a zero is required and comes from either the
output capacitor ESR or from a resistor R C in series with
C C . This simple model works well as long as the value of the
inductor is not too high and the loop crossover frequency
is much lower than the switching frequency. A phase lead
capacitor (C PL , LT3695 only) across the feedback divider
may improve the transient response. Figure 2 shows the
transient response when the load current is stepped from
300mA to 650mA and back to 300mA.
CURRENT MODE
POWER STAGE
SW
OUTPUT
g m = 1.25S
FB
R1
C PL
V OUT
100mV/DIV
g m = 430μS
ESR
3M
0.8V
+
C1
C1
I LOAD
0.5A/DIV
V C
GND
POLYMER
OR
CERAMIC
20μs/DIV
3695 F02
TANTALUM
C F
R C
C C
R2
OR
ELECTROLITIC
Figure 2. Transient Load Response of the LT3695
Regulators. A 3.3V OUT Typical Application with V IN = 12V
as the Load Current Is Stepped from 300mA to 650mA
3695 F01
Figure 1. Model for Loop Response. Note That R1 and R2 Are
Integrated in the LT3695-3.3 and LT3695-5
3695fa
17
相关PDF资料 |
PDF描述 |
|---|---|
| V300B5C150B2 | CONVERTER MOD DC/DC 5V 150W |
| LT1959CS8 | IC REG BUCK ADJ 4.5A 8SOIC |
| EYM24DTAD-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| LT3689HMSE-5#PBF | IC REG BUCK 5V 0.7A 16MSOP |
| MAX6724AUTRDD2+T | IC SUPERVISOR MPU SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3695HMSETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A Fault Tolerant Micropower Step-Down Regulator |
| LT3695IMSE#PBF | 功能描述:IC REG BUCK ADJ 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3695IMSE#TRPBF | 功能描述:IC REG BUCK ADJ 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3695IMSE-3.3#PBF | 功能描述:IC REG BUCK 3.3V 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3695IMSE-3.3#TRPBF | 功能描述:IC REG BUCK 3.3V 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。