- 您现在的位置：买卖IC网 > PDF目录13913 > LT3695HMSE#PBF (Linear Technology)IC REG BUCK ADJ 1A 16MSOP PDF资料下载
参数资料
| 型号： | LT3695HMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/30页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1A 16MSOP |
| 标准包装： | 37 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 20 V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 250kHz ~ 2.2MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LT3695 Series
PIN FUNCTIONS
(LT3695/LT3695-3.3, LT3695-5)
PGND (Pin 1, Exposed Pad Pin 17/Pin 1, Exposed Pad
Pin 17): This is the power ground used by the catch diode
(D1 in the Block Diagram) when its anode is connected to
the DA pin. The exposed pad may be soldered to the PCB
in order to lower the thermal resistance.
DA (Pin 2/Pin 2): Connect the anode of the catch diode
(D1) to this pin. Internal circuitry senses the current
through the catch diode providing frequency foldback in
extreme situations.
NC (Pins 3, 10, 12/Pins 3, 10, 15): No Connects. These
pins are not connected to internal circuitry and must be
left ?oating to ensure fault tolerance.
SW (Pin 4/Pin 4): The SW pin is the output of the internal
power switch. Connect this pin to the inductor, catch diode
and boost capacitor.
RUN/SS (Pin 5/Pin 5): The RUN/SS pin is used to put
the LT3695 regulators in shutdown mode. Tie to ground
to shut down the LT3695 regulators. Tie to 2.5V or more
for normal operation. RUN/SS also provides a soft-start
function; see the Applications Information section for
more information.
RT (Pin 6/Pin 6): Oscillator Resistor Input. Connect a
resistor from this pin to ground to set the switching
frequency.
SYNC (Pin 7/Pin 7): This is the external clock synchroni-
zation input. Ground this pin with a 100k resistor for low
ripple Burst Mode operation at low output loads. Tie to
0.8V or more for pulse-skipping mode operation. Tie to a
clock source for synchronization. Clock edges should have
rise and fall times faster than 1μs. Note that the maximum
V IN (Pin 8/Pin 8): The V IN pin supplies current to the
internal regulator and to the internal power switch. This
pin must be locally bypassed.
V C (Pin 9/Pin 9): The V C pin is the output of the internal
error ampli?er. The voltage on this pin controls the peak
switch current. Tie an RC network from this pin to ground
to compensate the control loop.
FB (Pin 11) LT3695: The LT3695 regulates the FB pin to 0.8V.
Connect the feedback resistor divider tap to this pin.
PG (Pin 13/Pin 11): The PG pin is the open-collector output
of an internal comparator. PG remains low until the FB pin
(LT3695) or the OUT1,2 pins (LT3695-3.3, LT3695-5) are
within 10% of the ?nal regulation voltage. PG output is
valid when V IN is above the minimum input voltage and
RUN/SS is high.
GND (Pin 14/Pin 12): The GND pin is the ground of all the
internal circuitry. Tie directly to the local GND plane.
OUT1, OUT2, (Pins 14, 13) LT3695-3.3, LT3695-5: These
pins connect to the anode of the boost Schottky diode and
also supply current to the internal regulator. They also
connect to the internal feedback resistors and must be
connected to the output.
BD (Pin 15) LT3695: This pin connects to the anode of
the boost Schottky diode and also supplies current to the
LT3695’s internal regulator.
BOOST (Pin 16/Pin 16): This pin is used to provide a
drive voltage, higher than the input voltage, to the internal
bipolar NPN power switch. Connect a capacitor (typically
0.22μF) between BOOST and SW.
load current depends on which mode is chosen. See the
Applications Information section for more information.
3695fa
9
相关PDF资料 |
PDF描述 |
|---|---|
| V300B5C150B2 | CONVERTER MOD DC/DC 5V 150W |
| LT1959CS8 | IC REG BUCK ADJ 4.5A 8SOIC |
| EYM24DTAD-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| LT3689HMSE-5#PBF | IC REG BUCK 5V 0.7A 16MSOP |
| MAX6724AUTRDD2+T | IC SUPERVISOR MPU SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3695HMSETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A Fault Tolerant Micropower Step-Down Regulator |
| LT3695IMSE#PBF | 功能描述:IC REG BUCK ADJ 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3695IMSE#TRPBF | 功能描述:IC REG BUCK ADJ 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3695IMSE-3.3#PBF | 功能描述:IC REG BUCK 3.3V 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3695IMSE-3.3#TRPBF | 功能描述:IC REG BUCK 3.3V 1A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。