- 您现在的位置：买卖IC网 > PDF目录1825 > LT3724EFE#PBF (Linear Technology)IC REG CTRLR BST INV PWM 16TSSOP PDF资料下载
参数资料
| 型号： | LT3724EFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/26页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST INV PWM 16TSSOP |
| 标准包装： | 95 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 225kHz |
| 占空比： | 100% |
| 电源电压： | 4 V ~ 60 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
| 产品目录页面： | 1332 (CN2011-ZH PDF) |
LT3724
PIN FUNCTIONS
V IN (Pin 1): The V IN pin is the main supply pin and should
be decoupled to SGND with a low ESR capacitor located
close to the pin.
NC (Pin 2): No Connection.
SHDN (Pin 3): The SHDN pin has a precision IC enable
threshold of 1.35V (rising) with 120mV of hysteresis. It is
used to implement an undervoltage lockout (UVLO) circuit.
See Application Information section for implementing a
UVLO function. When the SHDN pin is pulled below a
transistor V BE (0.7V), a low current shutdown mode is
entered, all internal circuitry is disabled and the V IN sup-
ply current is reduced to approximately 10μA. Typical
pin input bias current is <10μA and the pin is internally
clamped to 6V.
C SS (Pin 4): The soft-start pin is used to program the sup-
ply soft-start function. The pin is connected to V OUT via a
ceramic capacitor (C SS ) and 200kΩ series resistor. During
start-up, the supply output voltage slew rate is controlled
to produce a 2μA average current through the soft-start
coupling capacitor. Use the following formula to calculate
C SS for a given output voltage slew rate:
C SS = 2μA(t SS /V OUT )
See the application section for more information on setting
the rise time of the output voltage during start-up. Shorting
this pin to SGND disables the soft-start function.
BURST_EN (Pin 5): The BURST_EN pin is used to enable
or disable Burst Mode operation. Connect the BURST_EN
pin to ground to enable the burst mode function. Connect
the pin to V CC to disable the burst mode function.
V FB (Pin 6): The output voltage feedback pin, V FB , is
externally connected to the supply output voltage via a
resistive divider. The V FB pin is internally connected to
the inverting input of the error amplifier. In regulation,
V FB is 1.231V.
V C (Pin 7): The V C pin is the output of the error amplifier
whose voltage corresponds to the maximum (peak) switch
current per oscillator cycle. The error amplifier is typically
configured as an integrator circuit by connecting an RC
network from the V C pin to SGND. This circuit creates the
dominant pole for the converter regulation control loop.
Specific integrator characteristics can be configured to
optimize transient response. Connecting a 100pF or greater
high frequency bypass capacitor from this pin to ground
is recommended. When Burst Mode operation is enabled
(see Pin 5 description), an internal low impedance clamp
on the V C pin is set at 100mV below the burst threshold,
which limits the negative excursion of the pin voltage.
Therefore, this pin cannot be pulled low with a low imped-
ance source. If the V C pin must be externally manipulated,
do so through a 1kΩ series resistance.
SGND (Pin 8, 17): The SGND pin is the low noise ground
reference. It should be connected to the –V OUT side of the
output capacitors. Careful layout of the PCB is necessary
to keep high currents away from this SGND connection.
See the Application Information section for helpful hints
on PCB layout of grounds.
SENSE – (Pin 9): The SENSE – pin is the negative input for
the current sense amplifier and is connected to the V OUT
side of the sense resistor for step-down applications. The
sensed inductor current limit is set to 150mV across the
SENSE inputs.
SENSE + (Pin 10): The SENSE + pin is the positive input for
the current sense amplifier and is connected to the induc-
tor side of the sense resistor for step-down applications.
The sensed inductor current limit is set to 150mV across
the SENSE inputs.
PGND (Pin 11): The PGND pin is the high-current ground
reference for internal low side switch and the V CC regulator
circuit. Connect the pin directly to the negative terminal of
the V CC decoupling capacitor. See the Application Informa-
tion section for helpful hints on PCB layout of grounds.
3724fd
6
相关PDF资料 |
PDF描述 |
|---|---|
| LT3740EDHC#PBF | IC REG CTRLR BUCK PWM CM 16-DFN |
| LT3741EFE#PBF | IC REG CTRLR BUCK PWM CM 20TSSOP |
| LT3742EUF#PBF | IC REG CTRLR BUCK PWM CM 24-QFN |
| LT3748HMS#PBF | IC REG CTRLR FLYBK ISO CM 16MSOP |
| LT3757EDD#PBF | IC REG CTRLR BST FLYBK INV 10DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3724EFE-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, Current Mode Switching Regulator Controller |
| LT3724IFE | 制造商:Linear Technology 功能描述:DC DC Cntrlr Single-OUT Step Up/Step Down 4V to 60V Input 16-Pin TSSOP EP |
| LT3724IFE#PBF | 功能描述:IC REG CTRLR BST INV PWM 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LT3724IFE#PBF | 制造商:Linear Technology 功能描述:DC-DC CONVERTER BUCK 200KHZ 制造商:Linear Technology 功能描述:DC-DC CONVERTER, BUCK, 200KHZ, TSSOP-16 |
| LT3724IFE#TRPBF | 功能描述:IC REG CTRLR BST INV PWM 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。