- 您现在的位置：买卖IC网 > PDF目录15239 > LT3724MPFE#PBF (Linear Technology)IC REG CTRLR BST INV PWM 16TSSOP PDF资料下载
参数资料
| 型号： | LT3724MPFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/26页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST INV PWM 16TSSOP |
| 标准包装： | 95 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 225kHz |
| 占空比： | 100% |
| 电源电压： | 4 V ~ 60 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -55°C ~ 125°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
LT3724
APPLICATIONS INFORMATION
R SENSE =
(V IN(MAX) – V OUT ) ? V OUT
V IN(MAX) ? f SW
L ≥ V OUT ?
The basic LT3724 step-down (buck) application, shown
in the Typical Application on the front page, converts a
larger positive input voltage to a lower positive or negative
output voltage. This Application Information section assists
selection of external components for the requirements of
the power supply.
R SENSE Selection
The current sense resistor, R SENSE , monitors the inductor
current of the supply (See Typical Application on front
page). Its value is chosen based on the maximum required
output load current. The LT3724 current sense amplifier
has a maximum voltage threshold of, typically, 150mV.
Therefore, the peak inductor current is 150mV/R SENSE .
The maximum output load current, I OUT(MAX) , is the peak
inductor current minus half the peak-to-peak ripple cur-
rent, ?I L .
Allowing adequate margin for ripple current and external
component tolerances, R SENSE can be calculated as fol-
lows:
100mV
I OUT(MAX)
TypicalvaluesforR SENSE areintherangeof0.005Ω
to 0.05Ω.
Inductor Selection
The critical parameters for selection of an inductor are
minimum inductance value, volt-second product, satura-
tion current and/or RMS current.
The minimum inductance value is calculated as follows:
V IN(MAX) – V OUT
f SW ? V IN(MAX) ? ? I L
f SW is the switch frequency (200kHz).
The typical range of values for ?I L is (0.2 ? I OUT(MAX) ) to
(0.5 ? I OUT(MAX) ), where I OUT(MAX) is the maximum load
current of the supply. Using ?I L = 0.3 ? I OUT(MAX) yields a
good design compromise between inductor performance
versus inductor size and cost. Higher values of ?I L will
increase the peak currents, requiring more filtering on
the input and output of the supply. If ?I L is too high,
the slope compensation circuit is ineffective and current
mode instability may occur at duty cycles greater than
50%. Lower values of ?I L require larger and more costly
magnetics. A value of ?I L = 0.3 ? I OUT(MAX) produces a
±15% of I OUT(MAX) ripple current around the DC output
current of the supply.
Some magnetics vendors specify a volt-second product
in their datasheet. If they do not, consult the magnetics
vendor to make sure the specification is not being exceeded
by your design. The volt-second product is calculated as
follows:
Volt-second (μsec) =
The magnetics vendors specify either the saturation cur-
rent, the RMS current or both. When selecting an inductor
based on inductor saturation current, use the peak cur-
rent through the inductor, I OUT(MAX) + ?I L /2. The inductor
saturation current specification is the current at which
the inductance, measured at zero current, decreases by
a specified amount, typically 30%.
When selecting an inductor based on RMS current rating,
use the average current through the inductor, I OUT(MAX) .
The RMS current specification is the RMS current at which
the part has a specific temperature rise, typically 40°C,
above 25°C ambient.
After calculating the minimum inductance value, the volt-
second product, the saturation current and the RMS current
for your design, select an off-the-shelf inductor. A list of
magnetics vendors can be found at www.linear.com, or
contact the Linear Technology Application Department.
For more detailed information on selecting an inductor,
please see the “Inductor Selection” section of Linear
Technology Application Note 44.
Step-Down Converter: MOSFET Selection
The selection criteria of the external N-channel standard
level power MOSFET include on resistance(R DS(ON) ), re-
verse transfer capacitance (C RSS ), maximum drain source
voltage (V DSS ), total gate charge (Q G ), and maximum
continuous drain current.
3724fd
12
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3729EUH | IC REG CTRLR BUCK PWM CM 32-QFN |
| VI-25Z-EU-F1 | CONVERTER MOD DC/DC 2V 80W |
| SRP1040-R75M | INDUCTOR 750NH 22A SMD |
| LTC3880IUJ#TRPBF | IC REG CTRLR BUCK PWM CM 40-QFN |
| SRP1040-R56M | INDUCTOR 560NH 25A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3724MPFE-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, Current Mode Switching Regulator Controller |
| LT3726EGN | 制造商:Linear Technology 功能描述: |
| LT373L | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LT373LF | 制造商:EDSYN 功能描述:LONER Angle Face Soldring Tip High-Temperature Rated for Lead-Free Process W: .0 |
发布紧急采购，3分钟左右您将得到回复。