- 您现在的位置：买卖IC网 > PDF目录44986 > LT3740EDHC (LINEAR TECHNOLOGY CORP) 0.14 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | LT3740EDHC |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 0.14 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 5 X 3 MM, PLASTIC, MO-229WJED-1, DFN-16 |
| 文件页数： | 3/20页 |
| 文件大小： | 234K |
| 代理商： | LT3740EDHC |
LT3740
11
3740fc
APPLICATIONS INFORMATION
Once the value for L is known, the type of inductor must
be selected. High efciency converters generally cannot
afford the core loss found in low cost powdered iron cores;
instead use ferrite, molypermalloy or Kool Mμ cores. A
variety of inductors designed for high current, low voltage
applications are available from manufacturers such as
Sumida, Panasonic, Coiltronics, Coilcraft and Toko.
Schottky Diode D1 Selection
The Schottky diode D1 shown in Figure 4 conducts dur-
ing the dead time between the conduction of the power
MOSFET switches. It is intended to prevent the body diode
of the bottom MOSFET from turning on and storing charge
during the dead time, which can cause a modest (about
1%) efciency loss. The diode can be rated for about one
half of the full load current since it is on for only a fraction
of the duty cycle. In order for the diode to be effective, the
inductance between it and the bottom MOSFET must be
as small as possible, mandating that these components
be placed adjacently. Another important benet of the
Schottky diode is that it reduces the SW node ringing at
switching edges, which reduces the noise in the circuit
and also makes the MOSFETs more reliable.
CIN and COUT Selection
The input capacitance CIN is required to lter the square
wave current at the drain of the top MOSFET. Use a low ESR
capacitor sized to handle the maximum RMS current.
I
RMS ≈ IOUT(MAX)
V
OUT
V
IN
V
IN
V
OUT
1
This formula has a maximum at VIN = 2VOUT, where:
I
RMS =
1
2
I
OUT(MAX)
This simple worst-case condition is commonly used for
design because even signicant deviations do not offer
much relief. Note that ripple current ratings from capacitor
manufacturers are often based on only 2000 hours of life
which makes it advisable to derate the capacitor.
The selection of COUT is primarily determined by the ESR
required to minimize voltage ripple and load step transients.
The output ripple
ΔVOUT is approximately bounded by:
ΔV
OUT <ΔlL ESR +
1
8F
S COUT
Since
ΔIL increases with input voltage, the output ripple
is highest at maximum input voltage. Typically, once the
ESR requirement is satised, the capacitance is adequate
for ltering and has the necessary RMS current rating.
Multiple capacitors placed in parallel may be needed to
meet the ESR and RMS current handling requirements.
Dry tantalum, special polymer, aluminum electrolytic
and ceramic capacitors are all available in surface mount
packages. Special polymer capacitors offer very low ESR
but have lower capacitance density than other types.
Tantalum capacitors have the highest capacitance density
but it is important to only use types that have been surge
tested for use in switching power supplies. Aluminum
electrolytic capacitors have signicantly higher ESR, but
can be used in cost-sensitive applications providing that
consideration is given to ripple current ratings and long
term reliability. Ceramic capacitors have excellent low ESR
characteristics but can have a high voltage coefcient
and audible piezoelectric effects. The high Q of ceramic
capacitors with trace inductance can also lead to signicant
ringing. When used as input capacitors, care must be taken
to ensure that ringing from inrush currents and switching
does not pose an overvoltage hazard to the power switches
and controller. To dampen input voltage transients, add
a small 5μF to 50μF aluminum electrolytic capacitor with
an ESR in the range of 0.5Ω to 2Ω.
相关PDF资料 |
PDF描述 |
|---|---|
| LT3741EFE#PBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3741IFE#TRPBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3741EUF#PBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
| LT3741EUF#TRPBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
| LT3741IUF#PBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3740EDHC#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LT3740EDHC#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LT3740EDHC-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Wide Operating Range, Valley Mode, No RSENSE? Synchronous Step-Down Controller |
| LT3740EDHC-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Wide Operating Range, Valley Mode, No RSENSE? Synchronous Step-Down Controller |
| LT3740EDHC-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Wide Operating Range, Valley Mode, No RSENSE? Synchronous Step-Down Controller |
发布紧急采购，3分钟左右您将得到回复。