- 您现在的位置：买卖IC网 > PDF目录20978 > LT3745EUJ#PBF (Linear Technology)IC LED DVR 16CH 50MA 40-QFN PDF资料下载
参数资料
| 型号： | LT3745EUJ#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR 16CH 50MA 40-QFN |
| 标准包装： | 61 |
| 恒定电流： | 是 |
| 拓扑： | PWM，降压（降压） |
| 输出数： | 16 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 背光，通用 |
| 类型 - 次要： | 颜色 |
| 频率： | 200kHz ~ 1MHz |
| 电源电压： | 6 V ~ 55 V |
| 输出电压： | 36V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3745
OPERATION
The LT3745 integrates a single constant-frequency current-
mode nonsynchronous buck controller with sixteen linear
current sinks. The buck controller generates an adaptive
output LED bus voltage to supply parallel LED strings and
the sixteen linear current sinks regulate and modulate
individual LED strings. Its operation is best understood
by referring to the Block Diagram.
Start-Up
The LT3745 enters shutdown mode and drains almost zero
current when the EN/UVLO pin is lower than 0.35V. Once
the EN/UVLO pin is above 0.35V, the part starts to wake
up internal bias currents, generate various references,
and charge the capacitor C CAP towards 6.8V regulation
voltage. This V IN referenced voltage regulator (V IN - V CAP )
will supply the internal gate driver circuitry driving an
external P-channel MOSFET in normal operation. The
LT3745 remains in undervoltage lockout (UVLO) mode
as long as any one of the EN/UVLO, V CC , and (V IN - V CAP )
UVLO flags is high. Their UVLO thresholds are typically
1.31V, 2.89V, and 4.9V, respectively. After all the UVLO
flags are cleared, the buck controller starts to switch, and
the soft-start SS pin is released and charged by a 12μA
current source, thereby smoothly ramping up the inductor
current and the output LED bus voltage.
Power-on-Reset (POR)
During start-up, an internal power-on-reset (POR) high
signal blocks the input signals to the serial data interface
and resets all the internal registers except the 194-bit shift
register. The 1-bit frame select (FS) register, 1-bit enable
LED channel (EN) register, individual 12-bit grayscale (GS)
registers, and individual 6-bit dot correction (DC) registers
are all reset to zero. Thus all the LED channels are turned off
initially with the default grayscale (0x000) and dot correc-
tion (0x00) setting. Once the part completes its soft-start
(i.e., the SS pin voltage is higher than 1V) and the output
LED bus voltage is power good (i.e., within 5% of its FB
programmed regulation level), the POR signal goes low
to allow the input signals to the serial data interface. Any
fault triggering the soft-start will generate another POR
high signal and reset internal registers again.
Serial Data Interface
The LT3745 has a 30MHz, fully-buffered, skew-balanced,
cascadable serial data interface. The interface uses a novel
6-wire (LDI, SCKI, SDI, LDO, SCKO, and SDO) topology
and can be connected to microcontrollers, digital signal
processors (DSPs), or field programmable gate arrays
(FPGAs).
In a conventional 4-wire topology shown in Figure 1, the LDI
and SCKI signals need global routing while the SDI signal
only needs local routing between chips. Depending on the
number of chips in cascade and the size of system PCB
board, external clock-tree type buffers with corresponding
driving capability are needed for both the LDI and SCKI
signals to minimize signal skews. The propagation delay
caused by the buffer insertion on the SCKI signal yields
LT3745 6-WIRE TOPOLOGY
LDO
SCKO
SDO
LDI
SCKI
SDI
CHIP 1 LDO
SCKO
SDO
LDI
SCKI
SDI
CHIP 2 LDO
SCKO
SDO
LDI
SCKI
SDI
CHIP N LDO
SCKO
SDO
CONTROLLER
SDI
SCKI
LDI
CONVENTIONAL 4-WIRE TOPOLOGY
LDO
SCKO
SDO
LDI
SCKI
SDI
CHIP 1 LDO
SCKO
SDO
LDI
SCKI
SDI
CHIP 2 LDO
SCKO
SDO
LDI
SCKI
SDI
CHIP N LDO
SCKO
SDO
CONTROLLER
SDI
3745 F01
Figure 1. LT3745 6-Wire Topology vs Conventional 4-Wire Topology
3745f
13
相关PDF资料 |
PDF描述 |
|---|---|
| REC3-243.3SRW/H6/C/SMD-R | CONV DC/DC 3W 18-36VIN 3.3VOUT |
| MINT1065B2475C01 | PWR SPLY MED SWITCHER 65W 24V |
| MINT1065B1875C01 | PWR SPLY MED SWITCHER 65W 18V |
| REC3-243.3SRW/H6/A/SMD-R | CONV DC/DC 3W 18-36VIN 3.3VOUT |
| MINT1065B1575C01 | PWR SPLY MED SWITCHER 65W 15V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3745IUJ#PBF | 功能描述:IC LED DVR 16CH 50MA 40QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3745IUJ#TRPBF | 功能描述:IC LED DVR 16CH 50MA 40QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3745IUJ-1#PBF | 功能描述:IC LED DRVR 16CH 50MA 40QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3745IUJ-1#TRPBF | 功能描述:IC LED DRVR 16CH 50MA 40QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3746 | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel 50mA LED |
发布紧急采购，3分钟左右您将得到回复。